5040314 EVINRUDE * ROCKER SHAFT SPRING L=25


5040314 * ROCKER SHAFT SPRING L=25 EVINRUDE B10EL4AAA, B10EL4INS, B10PL4AAA, B10PL4INS, B10PX4INS, B10R4AAA, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4INS, B10TPX4INS
5040314 * ROCKER SHAFT SPRING L=25 EVINRUDE
Rating:
103

Buy * ROCKER SHAFT SPRING L=25 5040314 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

BRP EVINRUDE entire parts catalog list:

B10EL4AAA, E10EL4AAA 2012
B10EL4INS 2012
B10PL4AAA, B10PX4AAA, E10PL4AAA, E10PX4AAA 2012
B10PL4INS 2012
B10PX4INS, E10PX4INS 2012
B10R4AAA, B10RL4AAA, E10R4AAA, E10RL4AAA 2012
B10R4INS, E10R4INS 2012
B10RL4INS, E10RL4INS 2012
B10TEL4AAA, E10TEL4AAA 2012
B10TEL4INS, E10TEL4INS 2012
B10TPL4AAA, B10TPX4AAA, E10TPL4AAA, E10TPX4AAA 2012
B10TPL4INS, E10TPL4INS 2012
B10TPX4INS, E10TPX4INS 2012

Information:

2. Disconnect fuel lines (2) from fuel transfer pump (1).3. Remove the four bolts to remove fuel transfer pump (1) from the engine.Install Fuel Transfer Pump
1. Make a replacement of the O-ring seal on the fuel transfer pump if necessary. Put clean engine oil on the seal. 2. Put fuel transfer pump (1) in position on the engine oil pump. Make sure the drive coupling for the fuel transfer pump is engaged correctly with the engine oil pump shaft.3. Install the bolts that hold the fuel transfer pump.4. Connect fuel lines (2) to fuel transfer pump (1).5. Open the fuel supply line to the engine and use the fuel priming pump to remove (bleed) the air from the system.Disassemble Fuel Transfer Pump
Start By:a. remove fuel transfer pumpFluid Spillage Containment
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. 1. Put drive coupling (2) from the pump shaft2. Remove O-ring seal (1) from the pump. 3. Remove cap (6), seal washer (5), spring (4) and relief valve poppet (3) from the pump bracket assembly. 4. Remove bolts (7) and remove pump head (8) from plate (9). 5. If necessary, remove check valve (10) from head (8). 6. Remove plate (9) from the pump casing.7. Remove gasket (11) and the O-ring seal from the opposite side of plate (9).8. If necessary, remove the bearings from plate (9). 9. Remove gear assembly (12) and shaft assembly (13) from the pump bracket and casing (14). 10. Remove casing (14) and sleeves (15) from pump bracket (16).11. Remove the O-ring seal from casing (14). 12. Remove outer seal (17) and inner seal (18) from bracket (16).13. If necessary, remove the two bearings from bracket (16).Assemble Fuel Transfer Pump
1. Use Tooling (A) to install the inner and outer lip seals in bracket (1). Make sure the lips of the seals are in the position shown at assembly. Put clean engine oil on the lips of the seals. 2. Use Tooling (A) to install bearings (2) 1.5 mm (.06 in) below the surface of bracket (1). 3. Install sleeves (4) in bracket (1).4. Install O-ring seal (5) in casing (3) and put casing (3) over sleeves (4) on bracket (1). 5. Install gear assembly (6) and shaft assembly (7) in the bracket and casing. 6. Use Tooling (A) to install bearings (8) 1.5 mm (.06 in) below the surface of plate (9). 7. Install O-ring seal (10) in plate (9) and put plate (9) in position on the pump casing. 8. Use Tooling (A) to install the check valve in head (11) until it makes contact with the shoulder in its bore. Make sure the spring on the check valve is toward the inside before it is installed. 9. Put gasket (12) and head (11) in position on the plate and install the two bolts that hold the pump together. 10. Install the relief valve poppet (13), spring (14), the seal washer and cap (15) in the pump. 11. Install O-ring seal (16) around the pump and put clean engine oil on it.12. Install drive coupling (17) on the pump shaft.End By:a. install fuel transfer pump


Parts EVINRUDE:

5041199
 
5041199 * INTAKE VALVE STEM SEAL
B10EL4AAA, B10EL4INS, B10PL4AAA, B10PL4INS, B10PX4INS, B10R4AAA, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4INS, B3R4AAA, E15PL4INS, E15R4INS
5041467
 
5041467 * THROTTLE DECAL
B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15R4AAA, B15R4AAB, B3R4AAA, B4R4AAA, B4R4INS, B6R4AAA, B6R4INS, E10TEL4AAB
5040761
 
5040761 * PRIMER BULB
B10EL4INS, B10PL4INS, B10PX4INS, B10R4INS, B10RL4INS, B10TEL4INS, B10TPL4INS, B10TPX4INS, B15PL4INS, B15R4INS, B15RL4INS, B15TE4INS, B6R4INS, E10EL4INS, E10PL4INS, E15PL4INS, E15R4INS
5041480
 
5041480 * FLOAT CHAMBER
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, E10EL4AAB, E10EL4INS, E10PL4INS, E10TEL4AAB
5041286
 
5041286 * CARBURETOR COVER GASKET
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, E10EL4AAB, E10EL4INS, E10PL4INS, E10TEL4AAB
5040297
 
5040297 * GASKET DRAIN SCREW
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
5040346
 
5040346 * BRUSH HOLDER
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, E10EL4AAB, E10EL4INS, E10PL4INS, E10TEL4AAB
5041446
 
5041446 * CHOKE ROD
B10EL4INS, B10PX4INS, B10R4AAA, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4INS, B10TPX4INS, E10EL4INS
Back to top