0215742 115 - Front & Rear EVINRUDE
E115DBXAAA, E115DBXABA, E115DBXIIB, E115DBXINE, E115DBXISF, E115DBXSCR, E115DBXSEF, E115DBXSUC, E115DHLAAA, E115DHLABA, E115DHLIIR, E115DHLINA, E115DHLISC, E115DHLSES, E115DPLSCR, E115DPLSEF, E115DPLSUC, E130DPLAAA, E130DPLABA, E130DPLIIR, E130DPLINA
115
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- DECALS - Blue » 0215742
E115DBXIIB 2011
E115DBXINE 2012
E115DBXISF, E115DBXISM 2010
E115DBXSCR 2008
E115DBXSEF 2009
E115DBXSUC 2007
E115DHLAAA, E115DHLAAB, E115DPLAAA 2012
E115DHLABA, E115DPLABA 2012
E115DHLIIR, E115DPLIIB 2011
E115DHLINA, E115DPLINE 2012
E115DHLISC, E115DHLISF, E115DPLISF, E115DPLISM 2010
E115DHLSES 2009
E115DPLSCR 2008
E115DPLSEF 2009
E115DPLSUC 2007
E130DPLAAA, E130DPLAAB 2012
E130DPLABA 2012
E130DPLIIR 2011
E130DPLINA 2012
E130DPLISC, E130DPLISF 2010
E130DPLSES 2009
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
A(2) 585-0005 Crankshaft Turning Tool 1
B 1U-6684 Piston Ring Compressor 1
C - E12 Torx Socket 1
D 8T-3052 Degree Wheel 1
(1) This Tool is used in the aperture for the electric starting motor.
(2) The Crankshaft Turning Tool is used on the front pulley.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
If the connecting rod caps were temporarily installed, remove the connecting rod caps. If necessary, thoroughly clean all the components.
Apply clean engine oil to the cylinder bore, to the piston rings, to the outer surface of the piston and to the bearing shells for the connecting rod.Note: Install the bearing shells for the connecting rods dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the correct procedure. Apply clean engine oil to the bearing shells for the connecting rods during final assembly.Note: Ensure that the piston and the connecting rod assembly are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom center position. Lubricate the crankshaft pin with clean engine oil.
Illustration 1 g06361356
Install Tooling (B) onto piston (4). Ensure that the piston ring gaps are 120 degrees apart.Note: Ensure that Tooling (B) is installed correctly and that piston (4) can easily slide from the tool.Note: The arrow on the top of the piston must be toward the front of the engine. The locating tab for the bearing shell of the connecting rod must be on the same side of the engine as the piston cooling jet.
Carefully push the piston and the connecting rod assembly into the cylinder bore and onto the crankshaft pin.Note: Do not damage the finished surface of the crankshaft pin.
Illustration 2 g06360869
Install connecting rod cap (2) onto connecting rod (3).Note: Ensure that etched Number (Y) on connecting rod cap (2) matches etched Number (Y) on connecting rod (3). Ensure the correct orientation of connecting rod cap (2). The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old connecting rod bolts to secure the connecting rod cap.
Install new bolts (1) to connecting rod (3). Use Tooling (C) to tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts for an additional 120 degrees in a clockwise direction. Use Tooling (C) and Tooling (D) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft to ensure that there is no binding.
Repeat Step 2 through Step 9 to install the remaining pistons and connecting rods.End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install" for the correct procedure.
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for the correct procedure.
Parts 115 EVINRUDE:
0215808
0215808 115 H.O. - Front & Rear
E115DBXAAA, E115DBXABA, E115DBXIIB, E115DBXINE, E115DBXISF, E115DBXSEF, E115DHLAAA, E115DHLABA, E115DHLIIR, E115DHLINA, E115DHLISC, E115DHLSES, E115DPLSEF, E130DPLAAA, E130DPLABA, E130DPLIIR, E130DPLINA, E130DPLISC, E130DPLSES