0215750 EVINRUDE 175 - Front & Rear

} } @media print { div.divFooter { position: fixed; bottom: 0; right: 0; } } Caterpillar: Confidential Yellow
PSP FOR TIMING ADVANCE SLIPPAGE ON CERTAIN 3406B TRUCK ENGINES - EFFECTIVE OCTOBER 09, 1990 - PS6042 - THIS SL REPLACES POR TION OF MAY 17, 1990 SL - PS4300 - INVOLVING 3406B TRUCK ENGINES - MAILED US AND CANADA, COFA, CFEL, TRUCK TEPS - LIMITE D COSA
  The information supplied in this service letter may not be valid after the termination date of this program.   Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.
(Effective October 9, 1990) U-242 AU-153 E-148 O-183.5 TT-21 1272 PS6042 This Program can only be administered after a failure occurs. The decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS6042" as Part Number, "7755" as Group Number, and "96" as Description Code. This Service Letter replaces the portion of the May 17, 1990 Service Letter - PS4300 involving 3406B Truck Engines. Termination Date
December 31, 1991
Problem
The 7C5902 Body As. can slip in the 7W5242 Carrier As. in the Fuel Pump & Governor Drive Group (Timing Advance) used in certain 3406B Truck Engines (1988 model and later). The new parts listed under the heading Parts Neededwill not fit 1987 and earlier models.
Affected Product
Model Identification Number 3406B 4MG3600 - 92794
Parts Needed
1 - 7E2460 Race (use only if required) 1 - 7E8097 Carrier As. 4 - 7N7264 Weight (use only if required) 1 - 2W0459 Gasket 1 - 4W0436 Seal (use only if required) 2 - 4W2754 Seal (use only if required)
Action Required
See the attached procedure.
Service Claim Allowances
Product Caterpillar Dealer Suggested Customer Suggested miles/age Parts Labor Hrs. Parts Labor Hrs. Parts Labor Hrs. whichever comes first 0-300,000 100% 2.5 0 0 0 0 0-60 This is a 2.5-hour job.
Parts Disposition
Any parts removed (with the exception of cores used for Caterpillar Remanufactured parts) can be rendered useless and scrapped immediately upon completion of the repair. Attach. (1-Rework Procedure) Rework Procedure Many factors unrelated to the timing advance can contribute to poor truck performance. Refer to the Truck Performance Diagnostic Guide Form No. SEBD0808. If body/carrier slippage is suspected, pin the injection pump and remove the fuel pump & governor drive group (timing advance) from engine. Disassemble the timing advance for access to the body/carrier assembly. Engine Serial Numbers 4MG3600-16829 Perform the following inspection to determine body/carrier slippage: 1) Try to rotate the body in the carrier by hand. If the body slips in the carrier, install the parts listed under Parts Needed. 2) If the body does not rotate in the carrier, inspect the inside surface of the body which contacts the spline end of the fuel pump camshaft. A thin contact line on this surface is normal. If a wider contact line is present with evidence of metal displacement or spalling, body/carrier slippage has likely occurred. A second location to check is the other side of the body which contacts the large 8F1145 Lock Ring (See Illustration for wear locations). If the body has slipped, the harder ring material will wear (or polish) the outer contact face of the body. Look for polishing in the open area between the ends of the 8F1145 Lock Ring. If both wear conditions are found, install the parts listed under Parts Needed. Engine Serial Numbers 4MG16830-92794 On engines with serial numbers 4MG16830 and up, alignment marks are stamped on the front of the 7C5902 Body and 7W5242 Carrier (See Illustration). If the marks are aligned, body/carrier slippage has likely not occurred. Do not replace the parts. If the marks are not aligned (within 5 degrees), install the parts listed under Parts Needed. All Engine Serial Numbers Above Engine serial numbers 4MG57673 and up are equipped with dual 7E2460