0432829 AIR INLET, Stbd., 100STL EVINRUDE
E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100STLETS, E110MLCCA, E110MLCEM, E115JLEIE, E115JLEND, E115JLERC, E115JLETS, E115MLESB, E88MSLCCC, E88MSLCCC, E88MSLCER, E88MSLCER, E88MSLEIM, E88MSLEIM, E88MSLENB, E88MSLENB, E
AIR
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
E100STLCEM 1989
E100STLEIE, VE100SLEIE 1991
E100STLEND, VE100SLEND 1992
E100STLERC 1994
E100STLESB, VE100SLESB 1990
E100STLETS, VE100SLETS 1993
E110MLCCA, E110TLCCA, E110TXCCA 1988
E110MLCEM, E110TLCEM, E110TXCEM, TE110TLCEM, TE110TLESF, TE110TXCEM 1989
E115JLEIE, E115MLEIE, E115TLEIE, E115TXEIE, TE115TLEIE, VE115TLEIE, VE115TXEIE 1991
E115JLEND, E115MLEND, E115TLEND, E115TXEND, TE115TLEND 1992
E115JLERC, E115MLERS, E115TLERC, E115TXARS 1994
E115JLETS, E115MLETS, E115TLETS, E115TXATS, TE115TLETS, VE115TLETS 1993
E115MLESB, E115TLESB, E115TXESB, TE115TLESB, VE115TLESB, VE115TXESB 1990
E88MSLCCC, VE88MSLCCC 1988
E88MSLCCC, E90TLCCA 1988
E88MSLCER, E90TLCEM, TE90TLCEM, TE90TLESF 1989
E88MSLCER, VE88MSLCER 1989
E88MSLEIM, E90JLEIE, E90TLEIE, TE90TLEIE, VE90MLEIE, VE90TLEIE 1991
E88MSLEIM 1991
E88MSLENB 1992
E88MSLENB, E90JLEND, E90TLEND, TE90TLEND, VE90MLEND, VE90TLEND 1992
E88MSLERD, E90JLERC, E90MLERC, E90TLERC, E90TXARC 1994
E88MSLERD 1994
E88MSLESA, VE88MSLESA 1990
E88MSLESA, E90TLESB, TE90TLESB, TE90TLESF, VE90MLESB, VE90TLESB 1990
E88MSLETE 1993
E88MSLETE, E90JLETS, E90TLETS, E90TXATS, TE90TLETS, VE90MLETS, VE90TLETS 1993
Information:
Table 1
Tools Needed Quantity
279-3473 Barring and Mounting Gp 1
Ratchet wrench with a 34 mm socket 1
Torque wrench 1
Illustration 1 g02618278
279-3473 Barring and Mounting Gp
Testing and Adjusting
Illustration 2 g06083614
Location of Section A-A
Illustration 3 g02619977
Flywheel pin storage and top side pinning location (Section A-A)
(1) Timing port (top of flywheel housing)
(2) Plug
(3) Timing pin storage locations
(4) 311-6018 Timing Pin Assembly
Illustration 4 g03586264
(2) Timing plug
Illustration 5 g03377257
Barring tool installation and left side pinning location (Left side engine view)
(5) Barring tool
Check each timing pin storage location (3) for flywheel timing pin assembly (4). The correct pin is identified by the letter "F" that is stamped in the top of the bolt head of the timing pin. Remove the correct pin from storage.
Install the timing pin into the left-hand side timing port:
Remove plug (2) from timing port (1) in the flywheel housing.Note: There is a timing port for side pinning located on both sides of the engine.
Insert the timing pin into the timing port.
Use barring tool (5) and a ratchet wrench with a 34 mm socket to turn the flywheel in the direction of normal engine rotation. Turn the flywheel until the machined hole in the flywheel is aligned with the appropriate timing port:If the top timing port is used, drop the pin into the hole and slowly bar the engine over.If a side timing port is used, gently press the pin against the flywheel while you bar the engine over.
The pin will easily insert into the timing hole in the flywheel as the holes become aligned.Note: If the flywheel is turned beyond the point of engagement, the flywheel must be turned in the direction that is opposite of normal engine rotation. Turn the flywheel by approximately 30 degrees. Then turn the flywheel in the direction of normal engine rotation until the timing bolt engages with the threaded hole. This procedure will remove the play from the gears when the No. 1 piston is on the top center.
Remove the valve cover for the No. 1 cylinder head.
Illustration 6 g06084062
The inlet and exhaust valves for the No. 1 cylinder are fully closed if the No. 1 piston is on the compression stroke. With the engine having HLA's, there will not be any play in the rocker arms. In any position the rocker arms should always be tight. To verify, watch the push tubes on cylinder No. 1 and No. 7 for motion as you barred from 360 degrees from TDC. If the No. 1 push tubes are up, No. 1 is on the exhaust stroke. If the No. 7 push tube are up, No. 1 is on the compression stroke. Ensure the cylinders that will be checked or adjusted are on the correct crankshaft stroke position. Refer to Testing and Adjusting, "Valve Lash - Adjust (Hydraulic Lash Adjusters)".Note: When the actual stroke position is identified and the other stroke position is needed, remove the timing bolt from the flywheel. Turn the flywheel by 360 degrees in the direction of normal engine rotation.Torque specification for the timing port plug at the top of the flywheel housing: ... 100 20 N m (74 15 lb ft)
Parts air EVINRUDE:
0432828
0432828 AIR INLET, Port, 100STL
E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100STLETS, E110MLCCA, E110MLCEM, E115JLEIE, E115JLEND, E115JLERC, E115JLETS, E115MLESB, E88MSLCCC, E88MSLCCC, E88MSLCER, E88MSLCER, E88MSLEIM, E88MSLEIM, E88MSLENB, E88MSLENB, E