0206650 EVINRUDE APPLIQUE FRONT


0206650 APPLIQUE FRONT EVINRUDE 100193A, 125183C, 60172C, 85193A APPLIQUE
0206650 APPLIQUE FRONT EVINRUDE
Rating:
33

Buy APPLIQUE FRONT 0206650 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

100193A, 100193C 1971
125183C 1971
60172C, 60172E, 60173C, 60173E 1971
85193A, 85193H 1971

Information:


Refer to Systems Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Illustration 1 g01862457
Typical example (3) Clamp (4) Washer (5) O ring seal
Table 1
Specifications for 344-3316 Fuel Injector Gp    
Callout     Part Number     Part Name     Specification Description    
1     -     Nut     Torque to...................
2 N m (18 lb in)    
2     278-5170     Bolt     Torque to...................
21 N m (15.5 lb ft)    Removal Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     298-5564     T40 Torx Socket     1    
B     268-1968     Pry Bar     1    
C     370-8376     Cap Kit     1    Start By:
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft" for the correct procedure.
Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines" for the correct procedure.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Use a deep socket in order to remove the electrical connections from the electronic unit injectors. Use of incorrect tooling will result in damage to the electronic unit injectors.
Note: Place identification marks on all hoses, on all hose assemblies, on wires and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. Plugging all hose assemblies and tube assemblies will prevent fluid loss. Plugging all hose assemblies and tube assemblies will to keep contaminants from entering the system.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Illustration 2 g01971774
Place a suitable container below tube assembly (1) in order to catch any fuel that might be spilled.
Loosen the nut on hose assembly (3) in order to allow the fuel to drain from tube assembly (1) .
Remove hose assembly (3) from tube assembly (1). Remove O-ring seal (2) .
Use Tooling (C) in order to cap the hose assembly immediately. Use Tooling (C) in order to plug the tube assembly immediately.
Illustration 3 g01971773
Make a temporary mark on valve bridges (5) in order to show the location and orientation. Remove valve bridges (5) .Note: Identi


Parts applique EVINRUDE:

0206647
 
0206647 APPLIQUE, Motor cover
100193A, 125183C, 60172C, 85193A
0206652
 
0206652 APPLIQUE, Rear
100193A, 125183C, 85193A
0206596
 
0206596 APPLIQUE, Evinrude
100193A, 100293R, 125183C, 125283R, 40202E, 50172S, 50202C, 60172C, 65272S, 85193A, 85293R
Back to top