0207925 EVINRUDE APPLIQUE,Rear


0207925 APPLIQUE,Rear EVINRUDE 50902C, 55772D, 55874S, E50ECSR, E55RLCSA, E60ECSR APPLIQUE
0207925 APPLIQUE,Rear EVINRUDE
Rating:
63

Buy APPLIQUE,Rear 0207925 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$101.84
 

01-08-2019

Schunk: Schunk
SCHUNK 0207925 GZB-S Intermediate Sleeve, 50.5 mm Length, 20 mm - 8 mm
For internal coolant supply || Closed collar || Coolant proof up to max. 80 bar
Number on catalog scheme: 19
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

50902C, 50903C, 55974C, 55975C 1979
55772D, 55773D 1977
55874S, 55875S 1978
E50ECSR, E50ELCSR 1980
E55RLCSA 1980
E60ECSR, E60ELCSR 1980

Information:


Table 1
Diagnostic Trouble Codes for Analog Throttles
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
91-3 91-3 Accelerator Pedal Position 1 : Voltage Above Normal The Electronic Control Module (ECM) detects one of the following conditions:
The ECM has been powered for 3 seconds.
Diagnostic code 168-4 is not active.
3509 (262) codes are not active.
The setting for the upper diagnostic limit has been exceeded for one second.
If equipped, the warning lamp will come on. The diagnostic code will be logged.
29-3 774-3 Accelerator Pedal Position 2: Voltage Above Normal
91-4 91-4 Accelerator Pedal Position 1 : Voltage Below Normal The ECM detects one of the following conditions:
The ECM has been powered for 3 seconds.
Diagnostic code 168-4 is not active.
3510 (2131) codes are not active.
The setting for the lower diagnostic limit has been exceeded for one second.
If equipped, the warning lamp will come on. The diagnostic code will be logged.
29-4 774-4 Accelerator Pedal Position 2: Voltage Below Normal
Follow the troubleshooting procedure in order to identify the root cause of the fault. If a fault occurs with the primary throttle with secondary throttle is installed, the secondary throttle will be used until the fault is repaired.If a fault occurs with the secondary throttle, the engine will use the primary throttle until the fault is repaired.If a functional throttle is not available, the following conditions will occur:
The engine will default to the limp home speed.
If the engine speed is higher than the limp home speed, the engine will decelerate to the limp home speed.
If the engine speed is lower than the limp home speed, the engine speed will remain at the current speed.
The engine will remain at this speed while the diagnostic code remains active.
All inputs from the faulty throttle are ignored by the ECM until the fault is repaired.
All inputs from the repaired throttle will be ignored by the ECM until the keyswitch has been cycled.The diagnostic codes above relate to an analog sensor. Use this procedure only if the analog sensor uses an output from a variable resistor.The sensor is most likely to be mounted on a throttle pedal. The sensor is attached directly to the throttle assembly. The sensor provides an output voltage to the ECM. The sensor output voltage will vary with the position of the throttle. Foot operated or hand operated throttle assemblies are available.The sensor receives +5 V power from the ECM. The sensor will produce a raw signal voltage that will alter between low idle and high idle. The voltage is changed into a throttle position within the range 0% to 100% by the ECM.The sensor senses the speed requirement from the throttle position. A second sensor may override this speed requirement from the first sensor. This override will be subject to an input from a secondary throttle or from the SAE J1939 (CAN) data link or from a PTO control.Use the electronic service tool in


Parts applique EVINRUDE:

0207030
 
0207030 APPLIQUE
115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135383M, 135443B, 135543E, 135643D, 150840S, 175740S, 200640S, 50302R, 50442M, 50542B, 55642E, 55772D, 55874S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 75542B, 75642D, 85393M, 85493
0208328
 
0208328 APPLIQUE, Lever
100990S, 150940C, 50902C, 70973R
0208340
0208726
 
0208726 APPLIQUE,Front
E50ECSR, E55RLCSA, E60ECSR
0208920
 
0208920 APPLIQUE,Handle
E100MLCSC, E115MLCIH, E115MLCSA, E140MLCIH, E140MLCSA, E150TRLCIA, E150TRLCSF, E175TRLCIM, E175TRLCSA, E200TRLCIB, E200TRLCSF, E235TRLCIB, E235TRLCSM, E50BECIC, E50ECSR, E55RCIM, E55RLCSA, E60ECIA, E60ECSR, E70ELCIH, E70ELCSA, E75ERCIH, E75ERCSA, E85
0317107
 
0317107 APPLIQUE,Front
E55RLCSA, E60ECSR
Back to top