0207986 EVINRUDE APPLIQUE,Evinrude,port,140hp


0207986 APPLIQUE,Evinrude,port,140hp EVINRUDE 115790S APPLIQUE
0207986 APPLIQUE,Evinrude,port,140hp EVINRUDE
Rating:
63

Buy APPLIQUE,Evinrude,port,140hp 0207986 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Compatible models:

115790S   EVINRUDE

BRP EVINRUDE entire parts catalog list:

115790S, 140740S, 140743S, 140783S, 85790S 1977

Information:


Engine surfaces and fluids can be hot. A running engine will have moving belts exposed at the front of the engine (rear of bus). These hazards can result in personal injury or death. stop the engine while connecting test equipment and work carefully around a running engine. Do not allow tools or test equipment to protrude or vibrate into the path of rotating belts.
The guards must be in the proper place. Repair damaged guards or replace missing guards.
Wipe all caps and plugs before the engine is serviced in order to reduce the chance of system contamination.
For any type of leak (coolant, lube, or fuel) clean up the fluid. If leaking is observed, find the source and correct the leak. If leaking is suspected, check the fluid levels more often than recommended until the leak is found or fixed, or until the suspicion of a leak is proved to be unwarranted.
Accumulated grease and/or oil on an engine or deck is a fire hazard. Remove this debris with steam cleaning or high pressure water.
Ensure that the cooling lines are properly clamped and that the cooling lines are tight. Check for leaks. Check the condition of all pipes.
Inspect the water pumps for coolant leaks.Note: The water pump seal is lubricated by coolant in the cooling system. It is normal for a small amount of leakage to occur as the engine cools down and the parts contract.Excessive coolant leakage may indicate the need to replace the water pump seal. For the removal of water pumps and the installation of water pumps and/or seals, refer to the Service Manual for the engine or consult your Caterpillar dealer.
Inspect the lubrication system for leaks at the front crankshaft seal, the rear crankshaft seal, the oil pan, the oil filters and the valve cover.
Inspect the fuel system for leaks. Look for loose fuel line clamps or for loose fuel line tie-wraps.
Inspect the piping for the air inlet system and the elbows for cracks and for loose clamps. Ensure that hoses and tubes are not contacting other hoses, tubes, wiring harnesses, etc.
Inspect the alternator belt and the accessory drive belts for cracks, breaks or other damage.Belts for multiple groove pulleys must be replaced as matched sets. If only one belt is replaced, the belt will carry more load than the belts that are not replaced. The older belts are stretched. The additional load on the new belt could cause the belt to break.
Drain the water and the sediment from fuel tanks on a daily basis in order to ensure that only clean fuel enters the fuel system.
Inspect the wiring and the wiring harnesses for loose connections and for worn wires or frayed wires.
Inspect the ground strap for a good connection and for good condition.
Inspect the ECM to the cylinder head ground strap for a good connection and for good condition.
Disconnect any battery chargers that are not protected against the current drain of the starting motor. Check the condition and the electrolyte level of the batteries, unless the engine is equipped with a maintenance free battery.
Check the condition of the gauges. Replace any gauges that are cracked. Replace any gauge that can not be calibrated.


Parts applique EVINRUDE:

0207030
 
0207030 APPLIQUE
115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135383M, 135443B, 135543E, 135643D, 150840S, 175740S, 200640S, 50302R, 50442M, 50542B, 55642E, 55772D, 55874S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 75542B, 75642D, 85393M, 85493
0207784
 
0207784 APPLIQUE,Front,140hp
115790S, 115793S
0207972
 
0207972 APPLIQUE,Fron,140hp
115790S, 175740S, 70773S
0207985
Back to top