0209492 EVINRUDE APPLIQUE,Front


0209492 APPLIQUE,Front EVINRUDE E150TLCOS, E150TLCRD, E150TRLCTB, E175TLCOC, E175TRLCTD, E185TLCOC, E185TLCRS, E200TRLCTD, E235TLCOR, E235TLCRC, E235TRLCTD, E70ELCOS, E75ECOS APPLIQUE
0209492 APPLIQUE,Front EVINRUDE
Rating:
38

Buy APPLIQUE,Front 0209492 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

BRP EVINRUDE entire parts catalog list:

E150TLCOS, E150TXCOS 1985
E150TLCRD, E150TXCRD 1984
E150TRLCTB, E150TRLCTE, E150TRXCTB, E150TRXCTE 1983
E175TLCOC, E175TXCOC 1985
E175TRLCTD, E175TRLCTE, E175TRXCTD, E175TRXCTE 1983
E185TLCOC, E185TXCOC 1985
E185TLCRS, E185TXCRS 1984
E200TRLCTD, E200TRLCTS, E200TRXCTD, E200TRXCTS 1983
E235TLCOR, E235TXCOR 1985
E235TLCRC, E235TXCRC 1984
E235TRLCTD, E235TRLCTS, E235TRXCTD, E235TRXCTS 1983
E70ELCOS, E70TLCOS 1985
E75ECOS 1985

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
A(2) 585-0005 Crankshaft Turning Tool 1
B 1U-6684 Piston Ring Compressor 1
C - E12 Torx Socket 1
D 8T-3052 Degree Wheel 1
(1) This Tool is used in the aperture for the electric starting motor.
(2) The Crankshaft Turning Tool is used on the front pulley.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
If the connecting rod caps were temporarily installed, remove the connecting rod caps. If necessary, thoroughly clean all the components.
Apply clean engine oil to the cylinder bore, to the piston rings, to the outer surface of the piston and to the bearing shells for the connecting rod.Note: Install the bearing shells for the connecting rods dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the correct procedure. Apply clean engine oil to the bearing shells for the connecting rods during final assembly.Note: Ensure that the piston and the connecting rod assembly are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom center position. Lubricate the crankshaft pin with clean engine oil.
Illustration 1 g06361356
Install Tooling (B) onto piston (4). Ensure that the piston ring gaps are 120 degrees apart.Note: Ensure that Tooling (B) is installed correctly and that piston (4) can easily slide from the tool.Note: The arrow on the top of the piston must be toward the front of the engine. The locating tab for the bearing shell of the connecting rod must be on the same side of the engine as the piston cooling jet.
Carefully push the piston and the connecting rod assembly into the cylinder bore and onto the crankshaft pin.Note: Do not damage the finished surface of the crankshaft pin.
Illustration 2 g06360869
Install connecting rod cap (2) onto connecting rod (3).Note: Ensure that etched Number (Y) on connecting rod cap (2) matches etched Number (Y) on connecting rod (3). Ensure the correct orientation of connecting rod cap (2). The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old connecting rod bolts to secure the connecting rod cap.
Install new bolts (1) to connecting rod (3). Use Tooling (C) to tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts for an additional 120 degrees in a clockwise direction. Use Tooling (C) and Tooling (D) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft to ensure that there is no binding.
Repeat Step 2 through Step 9 to install the remaining pistons and connecting rods.End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install" for the correct procedure.
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for the correct procedure.


Parts applique EVINRUDE:

0327490
 
0327490 APPLIQUE
C155WTLM, CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, E100STLCCA, E100STLCEM, E100STLESB, E100WMLCDR, E100WMLCOC, E100WMLCRS, E100WTLCUA, E100WTLESM, E100WTLZ, E10EESC, E110MLCCA, E110MLCDC, E110MLCEM, E110MLCUR, E115MLCNB, E115MLCOS, E115MLCRD,
0327851
 
0327851 APPLIQUE
E115MLCTE, E140MLCTE, E150TRLCTB, E175TRLCTD, E200TRLCTD, E235TRLCTD, E70ELCTE, E75ERCTE, E90MLCTE
0209493
 
0209493 APPLIQUE,Evinrude,stbd. & port
E150TLCRD, E150TRLCTB, E175TRLCTD, E185TLCRS, E200TRLCTD, E235TLCRC, E235TRLCTD
0328937
 
0328937 APPLIQUE, Rear
E115MLCRD, E140TLCRD, E150TLCRD, E185TLCRS, E20CRCOS, E235TLCRC, E25ECOC, E30ECOA, E40ECOB, E40ECRM, E50BECOB, E60ELCOD, E70ELCRD, E75ECRD, E90MLCRD
0209788
 
0209788 APPLIQUE, Front
E70ELCOS, E70ELCRD, E75ECOS, E75ECRD
0209863
 
0209863 APPLIQUE, Engine cover, rear, 235
E150TLCRD, E185TLCRS, E235TLCRC
0329950
 
0329950 APPLIQUE, Front
E150TLCOS, E175TLCOC, E185TLCOC, E235TLCOR
0329959
 
0329959 APPLIQUE, Engine cover, rear
E150TLCOS, E175TLCOC, E185TLCOC, E235TLCOR
Back to top