0211021 EVINRUDE APPLIQUE, Rear


0211021 APPLIQUE, Rear EVINRUDE M55RWLR, R45RCLR APPLIQUE
0211021 APPLIQUE, Rear EVINRUDE
Rating:
78

Buy APPLIQUE, Rear 0211021 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

Compatible models:

M55RWLR   R45RCLR   EVINRUDE

BRP EVINRUDE entire parts catalog list:

M55RWLR 1988
R45RCLR, R45RCR 1988

Information:


Table 1
J1939 Code and Description Comments
632-5
Engine Fuel Shutoff Valve #1 : Current Below Normal This code indicates that there is a problem with the Gas Shutoff Valve ( GSOV) and/or the electrical circuit on the ECM.
632-6
Engine Fuel Shutoff Valve #1 : Current Above Normal This code indicates that there is a problem with the Gas Shutoff Valve ( GSOV) and/or the electrical circuit on the ECM.
677–5
Engine Starter Motor Relay : Current Below Normal This code indicates that there is a problem with the starter motor relay and/or electrical circuit on the ECM.
677–6
Engine Starter Motor Relay : Current Above Normal This code indicates that there is a problem with the starter motor relay and/or electrical circuit on the ECM.
1443–5
Engine Fuel Valve #2 Position : Current Below Normal This code indicates that there is a problem with the auxiliary fuel metering valve and/or the electrical circuit on the ECM.
1443–6
Engine Fuel Valve #2 Position : Current Above Normal This code indicates that there is a problem with the auxiliary fuel metering valve and/or the electrical circuit on the ECM.
2807–5
Engine Fuel Shutoff Valve #2 : Current Below Normal This code indicates that there is a problem with the auxiliary gas shutoff valve and/or the electrical circuit on the ECM.
2807–6
Engine Fuel Shutoff Valve #2 : Current Above Normal This code indicates that there is a problem with the auxiliary gas shutoff valve and/or the electrical circuit on the ECM.
2634-5
Power Relay : Current Below Normal This code indicates that there is a problem with the relay and/or electrical circuit from the ECM.
Relay powers the following:
- Fuel actuator
- Throttle actuator
- Turbo compressor bypass actuator
2634-6
Power Relay : Current Above Normal This code indicates that there is a problem with the relay and/or electrical circuit from the ECM.
Relay powers the following:
- Fuel actuator
- Throttle actuator
- Turbo compressor bypass actuator
4210-5
Engine Pre-lube Drive : Current Below Normal This code indicates that there is a problem with the prelubrication relay and/or the electrical circuit on the ECM.
4210-6
Engine Pre-lube Drive : Current Above Normal This code indicates that there is a problem with the prelubrication relay and/or the electrical circuit on the ECM.
4245-5
Fuel Energy Content : Current Below Normal This code indicates that there is a problem with the input from the fuel quality sensor.
4245-6
Fuel Energy Content : Current Above Normal This code indicates that there is a problem with the input from the fuel quality sensor. Electrical Checkouts on the Cat® Electronic Technician (ET)
Table 2
Component Electrical Checkout
Engine Starter Solenoid Attempt to start the engine. Refer to the application-specific schematic for the "Engine Starter Motor Solenoid" wiring circuit.
Engine Starter Motor Relay Attempt to start the engine. Once the ECM attempts to energize the solenoid, the code will become active. Refer to the application-specific schematic for the "Engine Starter Motor Relay" wiring circuit.
Prelubrication System Relay Prelubrication Relay Override
Fuel Actuator Power Supply Relay Turn main disconnect switch to the "ON" position.
Gas Shutoff Valve #1 Attempt to start the engine.
Once the ECM attempts to energize the relay coil, the code will become active.
Auxiliary Gas Shutoff Valve Attempt to start the engine.
Once the ECM attempts to energize the valve coil, the code will become active.
Valve coil resistance is 18.0 ohms to 27.0 ohms
Auxiliary Fuel Metering Valve Attempt to start the engine.
Once the ECM attempts to energize the valve coil, the code will become active.
Valve coil resistance is 3.0 ohms to 5.5 ohms.
Illustration 1 g06121236
For the complete circuit details, refer to the full schematic.
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -5 code is active or logged.
Proceed to Test Step 2.
Result: A -6 code is active or logged.
Proceed to Test Step 3.
2. Check the Wiring for an Open Circuit
A. Verify that the harness connector is free of debris, free of corrosion and securely connected.
B. Disconnect the harness from the solenoid, relay, or valve coil.
C. Connect a jumper wire between the terminals of the harness connector for the affected coil. The coil is replaced with a short circuit.
Create a Short
Result: A -5 code became active during the electrical checkout. The ECM did not detect the jumper wire. There is an open circuit in the wiring between the coil and the ECM connector. There may be a problem with a connector.
Repair: Repair or replace the connectors or the wiring.
Verify that the repair eliminated the problem.
Result: A -6 code is activated during the electrical checkout. The ECM detected the jumper wire. There is a problem with the solenoid, relay, or valve coil.
Repair: Replace the solenoid, relay, or valve coil.
Verify that the repair eliminated the problem.
3. Check the Wiring for a Short Circuit
A. Disconnect the harness from the solenoid, relay, or valve coil.
Create an Open
Result: A -6 code became active during the electrical checkout. The ECM did not detect the open circuit. There is a short circuit in the wiring between the coil and the ECM connector. There may be a problem with a connector.
Repair: Repair or replace the connectors or the wiring.
Verify that the repair eliminated the problem.
Result: A -5 code is activated during the electrical checkout. The ECM detected the open circuit. There is a problem with the solenoid, relay, or valve coil.
Repair: Replace the solenoid, relay, or valve coil.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts applique EVINRUDE:

0334008
 
0334008 APPLIQUE, Jo.
E100WTLEIB, E100WTLENE, E100WTLESM, E100WTLETD, E100WTLZ, E25RWESA, E25RWK, E45RCE, E45RCEIA, E45RCENM, E45RCESR, E45RCETB, E55RWLE, E55RWLEIA, E55RWLENM, E55RWLESR, E55RWLETB, E65WMLEIB, E65WMLENE, E65WMLESM, E65WMLETD, M55RWLR, R45RCLR, U25RWA, W10
0211023
 
0211023 APPLIQUE, Ev.
E100WTLEIB, E100WTLENE, E100WTLESM, E100WTLETD, E100WTLZ, E25RWESA, E25RWK, E45RCE, E45RCEIA, E45RCENM, E45RCESR, E45RCETB, E55RWLE, E55RWLEIA, E55RWLENM, E55RWLESR, E55RWLETB, E65WMLEIB, E65WMLENE, E65WMLESM, E65WMLETD, M55RWLR, R45RCLR, U25RWA, W10
0211022
 
0211022 APPLIQUE, Front
M55RWLR, R45RCLR
0334066
 
0334066 APPLIQUE, Front handle
E40WREES, E40WRLSIR, E40WRLSSC, E45RCE, E45RCEIA, E45RCENM, E45RCEOD, E45RCERE, E45RCESR, E45RCETB, E45RCLEDS, E45RCLEUC, E55RSLC, E55RSLG, E55RSLW, E55RWLE, E55RWLEIA, E55RWLENM, E55RWLERE, E55RWLESR, E55RWLETB, E55WREES, E55WRLSIR, E55WRLSSC, M55RW
0334065
 
0334065 APPLIQUE, Rear handle
E40WREES, E40WRLSIR, E40WRLSSC, E45RCE, E45RCEIA, E45RCENM, E45RCEOD, E45RCERE, E45RCESR, E45RCETB, E45RCLEDS, E45RCLEUC, E55RSLC, E55RSLG, E55RSLW, E55RWLE, E55RWLEIA, E55RWLENM, E55RWLERE, E55RWLESR, E55RWLETB, E55WREES, E55WRLSIR, E55WRLSSC, M55RW
0333746
 
0333746 APPLIQUE, Engine cover, rear
C155WTLM, E125ESXESS, E125ESXW, E150WTLETG, E155WTLEIB, E155WTLENE, E155WTLESM, E155WTLZ, E185ESXESS, E185ESXW, E200CXCEA, E200CXESM, E225CXCED, E225CXESS, E45RCE, E45RCEIA, E45RCENM, E45RCESR, E45RCETB, E55RWLE, E55RWLEIA, E55RWLENM, E55RWLESR, E55R
Back to top