0393078 EVINRUDE APPLIQUE, Front


0393078 APPLIQUE, Front EVINRUDE E150TRLCNM, E175TRLCNB, E200TRLCNE, E235TRLCNE APPLIQUE
0393078 APPLIQUE, Front EVINRUDE
Rating:
78

Buy APPLIQUE, Front 0393078 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
 
$427.49
 

12-09-2017
10.00[4.50] pounds
K&M Ma: K&M Manufacturin
K&M 039-3078 John Deere New Series KM 1015-3500 High Mounting Bracket
Mounting Bracket||All hardware has corrosion resistant coating||For KM 1015-13500
Number on catalog scheme: 19
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E150TRLCNM, E150TRXCNM 1982
E175TRLCNB, E175TRXCNB 1982
E200TRLCNE, E200TRXCNE 1982
E235TRLCNE, E235TRXCNE 1982

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Capping Kit 1
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Illustration 1 g02210473
Clean the area around flow control valve (3) and fuel injection pump. Ensure that the area is free from contamination before beginning disassembly.
Disconnect harness assembly (1) from flow control valve (3).
Disconnect plastic tube assembly (4). Use Tooling (A) to plug and cap the open port on the fuel injection pump and the plastic tube assembly.
Make temporary marks on flow control valve (3) and the fuel injection pump for installation purpose.
Remove allen heads screws (2) from flow control valve (3).
Remove flow control valve (3) from the fuel injection pump.
Remove O-ring seal (5) from fuel injection pump.Installation Procedure
Ensure that all component at free from wear and damage. If any part of the flow control valve is worn or damaged, the flow control valve must be replaced as an assembly. The flow control valve kit contains the guide pins to install the flow control valve assembly.
Illustration 2 g02208673
Illustration 3 g02306933
Flow control valve guide pins
Position a new O-ring seal (5) onto the flow control valve assembly.
Check O-ring seal (6) is correctly positioned. Ensure that O-ring seal (6) is not damaged.Note: If O-ring seal (6) is damaged, a new flow control valve assembly must be installed.
Install guide pins into Position (X) on the fuel injection pump.Note: Note that the guide pins are part of the flow control valve repair kit.
Lubricate O-ring seal (6) with clean fuel.Note: Ensure that the O-ring seal is not damaged or misaligned.
Align flow control valve (3) onto guide pins.
Install flow control valve (3) to the fuel injection pump.
Remove guide pins from the fuel injection pump.
Install allen head screws (2) from the flow control valve repair kit.
Tighten allen head screws (2) equally until the flow control valve is seated correctly onto the fuel injection pump.Note: Ensure that the allen head screws are tightened equally. Failure to ensure that the allen head screws are tightened equally will result in damage to the fuel injection pump.
Tighten the allen head screws to a torque of 9 N m (80 lb in).
Connect harness assembly (1) to flow control valve (3).
Remove plug and cap from ports from the fuel injection pump and the plastic tube assembly.
Connect plastic tube assembly (4).
Replace the filters for primary fuel system. Refer to Operation and Maintenance Manual, "Fuel System Primary (Water Separator) Element - Replace" for the correct procedure.
Replace the filters for secondary fuel system. Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Turn the fuel supply to the ON position.
Turn the battery disconnect switch to the ON position.
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for more information.End By:
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.
After replacement of the flow control valve, the fuel injection pump requires a high-pressure fuel pump calibration procedure to be performed. Refer to Troubleshooting, "Fuel Rail Pressure Problem" for the correct procedure.


Parts applique EVINRUDE:

0327490
 
0327490 APPLIQUE
C155WTLM, CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, E100STLCCA, E100STLCEM, E100STLESB, E100WMLCDR, E100WMLCOC, E100WMLCRS, E100WTLCUA, E100WTLESM, E100WTLZ, E10EESC, E110MLCCA, E110MLCDC, E110MLCEM, E110MLCUR, E115MLCNB, E115MLCOS, E115MLCRD,
0209215
 
0209215 APPLIQUE, Rear
E150TRLCNM, E175TRLCNB, E200TRLCNE, E235TRLCNE
0209216
 
0209216 APPLIQUE, Evinrude, stbd.& port.
E150TRLCNM, E175TRLCNB, E200TRLCNE, E235TRLCNE
0209214
 
0209214 APPLIQUE, Front
E150TRLCNM, E175TRLCNB, E200TRLCNE, E235TRLCNE
0209222
 
0209222 APPLIQUE
E150TRLCNM, E175TRLCNB, E200TRLCNE, E235TRLCNE
0209220
 
0209220 APPLIQUE
E150TRLCNM, E175TRLCNB, E200TRLCNE, E235TRLCNE
0209224
 
0209224 APPLIQUE
E150TRLCNM, E175TRLCNB, E200TRLCNE, E235TRLCNE
0209218
 
0209218 APPLIQUE
E150TRLCNM, E175TRLCNB, E200TRLCNE, E235TRLCNE
Back to top