0580767 EVINRUDE ARMATURE PLATE ASSEMBLY


0580767 ARMATURE PLATE ASSEMBLY EVINRUDE 4006E, 4106D, 4206S, 4306C, 4406R, 4506A, 4606M, 4902B ARMATURE
0580767 ARMATURE PLATE ASSEMBLY EVINRUDE
Rating:
68

Buy ARMATURE PLATE ASSEMBLY 0580767 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 58076
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

4006E, 4007E, 4036E, 4037E 1970
4106D, 4107D, 4136D, 4137D 1971
4206S, 4236S 1972
4306C, 4336C 1973
4406R, 4436R 1974
4506A, 4536A 1975
4606M, 4636M 1976
4902B, 4906B, 4936B 1969

Information:

1. Remove bolts (2) and pull governor drive (1) from the front drive housing. 2. Make sure the O-ring seals are in position on the front of governor drive (1) and put clean engine oil on the seals.3. Put governor drive (1) in position and install bolts (2) to hold it to the front drive housing.end by:a) install governorDisassemble Governor Drive
start by:a) remove governor drive 1. Remove O-ring seals (1), (2) and (3) from the front of the governor drive housing. 2. Remove the bolts that hold adapter (4) in position and pull adapter (4) from the housing.3. Remove pinion (5), shims (6), seals (7) and (8) from adapter (4). Make a measurement of the thickness of shims (6) and put identification on them for assembly purposes. 4. Remove hose assembly (9), cover (11) and the gasket from governor drive housing (10). 5. Remove gear (13) and coupling (12) from housing (10) as a unit. 6. Remove ring (14) to remove coupling (12) from gear (13). 7. If necessary, remove bearing (15) from housing (10).Assemble Governor Drive
1. Make an alignment of the oil hole in the bearing with the drilled oil passage in governor drive housing (1). Use tool group (A) and install the bearing in housing (1) until it is 1.0 0.5 mm (.039 .020 in.) below the inside surface of the housing. 2. Put coupling (3) in position in gear (2) and install ring (4) to hold the gear and coupling as a unit. 3. Install coupling (3) and gear (2) as a unit in housing (1). 4. Install pinion (5) in adapter (6). 5. Put adapter (6) and shims (7) of the original thickness in position and install the bolts to hold the unit together. 6. Make an adjustment of the gear clearance (backlash) between gear (2) and the pinion as follows: a) Install tool group (B) on gear (2) as shown to check the gear clearance (backlash) at four locations around gear (2) 90° apart.b) Hold the pinion in position and push down while gear (2) is moved back and forth. Make a record of the indications on tool group (B) and use the lowest indication as the correct gear clearance (backlash) value. The correct gear clearance (backlash) is 0.100 + 0.050 or - 0.025 mm (.0039 + .0020 or - .0010 in.).c) Add or subtract shims (7) as necessary until the gear clearance (backlash) is correct.7. Remove tool group (B), the adapter and pinion from the housing. 8. Connect hose assembly (8) to housing (1). Put the gasket and cover (9) in position and install the bolts and washers to hold them to housing (1). 9. Install seals (10) and (11) on adapter (6) and put clean engine oil on them.10. Install the correct amount of shims (7) and adapter (6) with the pinion in housing (1) and tighten the bolts. 11. If necessary, make a replacement of pins (14). Make sure the pins are 14 1 mm (.55 .04 in.) above the surface of the housing.12. Install O-ring seal (12) and seals (13) on the front of the housing. Put clean engine oil on the seals.end by:a) install governor


Parts armature EVINRUDE:

0580642
 
0580642 ARMATURE PLATE & POST
3802A, 4006E, 4106D, 4206S, 4306C, 4406R, 4506A, 4606M, 4902B
Back to top