5031682 ARMATURE EVINRUDE
E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC
ARMATURE
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$41.29
13-10-2020
4.40924524[1.80] Pounds
-: -
Connected Essentials 5031682 Tailored Heavy Duty Custom Fit Car Mats, for Touran Oval Clips (2006-2010), Black with Red Trim, Premium
Complete set of 6 tailored custom fit car mats - designed and manufactured specifically for Volkswagen Touran Oval Clips (2006-2010) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Complete set of 6 tailored custom fit car mats - designed and manufactured specifically for Volkswagen Touran Oval Clips (2006-2010) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
BRP EVINRUDE entire parts catalog list:
- POWER TRIM-TILT HYDRAULIC » 5031682
E50PL4EES 1999
E50PL4EES 1999
E50PL4SSC 2000
E50PL4SSC 2000
Information:
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     385-1861     Connector Plug     2    
B     352-5891     Lifting Strap     2    
C     -     Loctite 771     -    Start By:
Remove the clean emissions module.
Connect the engine to Caterpillar Electronic Technician (Cat ET) before the DPF is removed from the engine. Once the engine is connected to Cat ET, then perform an ash service test. This test is a manual regeneration. Allow the DPF to cool before proceeding.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.
Illustration 1 g02798250
Put Identification Marks (X) on both sides of clamp assemblies (6) and (7) for installation purposes.
Put Identification Mark (Y) on the diesel particulate filter (4) for installation purposes. Identification Mark (Y) is showing the flow of exhaust gases through the diesel particulate filter.
Disconnect harness assembly (1) .
Disconnect hose assemblies (2) and cap with Tooling (A) .
Loosen clamp assembly (3) .
Disconnect temperature sensor (8). Disconnect tube assemblies (9) from both ends of diesel particulate filter (4) .
Loosen clamp assemblies (5) .
Use Tooling (B) and a suitable lifting device to remove diesel particulate filter (4). The weight of diesel particulate filter (4) is approximately 57 kg (126 lb).
Discard clamp assemblies (3) and (5) .Installation Procedure
Note: When installing a new diesel particulate filter or a cleaned diesel particulate filter, an Ash Model reset must be performed. Refer to Special Instruction, REHS8180, "Aftertreatment Filter Maintenance on Tier 4 Final Products Equipped with a Diesel Particulate Filter (DPF), Diesel Oxidation Catalyst (DOC), and a Selective Catalyst Reduction (SCR) Filter" for the correct procedure.
Install diesel particulate filter (4) in the reverse order of removal.
Illustration 2 g02798280
Note: Do not use power tools in order to torque clamp assemblies (5) .
Apply Tooling (C) to the threads of clamp assemblies (5) along Distance (Z). Distance (Z) is 25 mm (1.0 inch) above the trunnion. Tighten clamp assemblies (5) to a torque of 16.5 1.5 N m (146 13 lb in).
Illustration 3 g02798274
Cutaway view of clamp assembly (3) in position on the assembly.Note: Do not use power tools in order to torque clamp assembly (3) .
Verify that the cup of the Ball Joint (G) does not touch the radius of the Ball (F). Position ball clamp assembly (3) and hand tighten clamp assembly (3). Clamp assembly (3) should be in the center of the joint.
Dimension (D) and Dimension (E) should be equal within 2.0 mm (0.08 inch). Repeat the measurements every 90° around clamp assembly (3). If necessary, adjust clamp assembly (3) .
Torque clamp assembly (3) to a torque of 35 2 N m (26 1 lb ft).
Tighten temperature sensor (8) to a torque of 45 5 N m (33 4 lb ft).
Parts armature EVINRUDE:
5031084
5031084 ARMATURE
E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC