0322985 EVINRUDE BASE, Air silencer


0322985 BASE, Air silencer EVINRUDE 100990S, 115890C, E100MLCSC, E115MLCIH, E115MLCSA, E140MLCIH, E140MLCSA, E85MLCSA, E90MLCIH BASE
0322985 BASE, Air silencer EVINRUDE
Rating:
78

Buy BASE, Air silencer 0322985 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$26.52
 

04-06-2022

-: -
0322985 Mast Bushing for Hyster
Upright || Upright, Bushings
Number on catalog scheme: 28
 

BRP EVINRUDE entire parts catalog list:

100990S, 100993S, 100999S, 115990R, 115993R, 115999R, 140940R, 140943R, 140983R, 85990R, 85995R, 85999R 1979
115890C, 115893C, 115899C, 140840C, 140843C, 140883C, 85890C, 85895C, 85899C 1978
E100MLCSC, E100TLCSC, E100TXCSC 1980
E115MLCIH, E115MLCIM, E115TLCIH, E115TLCIM, E115TXCIH, E115TXCIM 1981
E115MLCSA, E115TLCSA, E115TXCSA 1980
E140MLCIH, E140MLCIM, E140TRLCIH, E140TRLCIM, E140TRXCIH, E140TRXCIM 1981
E140MLCSA, E140TRLCSA, E140TRXCSA 1980
E85MLCSA, E85STLCSA, E85STXCSA 1980
E90MLCIH, E90MLCIM, E90TLCIH, E90TLCIM, E90TXCIH, E90TXCIM 1981

Information:


Illustration 1 g01173118
Schematic
Illustration 2 g01173384
P1 ECM connector (P1-22) Emergency stop switch (P1-23) Maintenance clear switch (P1-40) Diagnostic reset switch (P1-47) Low idle switchTest Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch OFF.
Thoroughly inspect the J61/P61 customer connector, the J1/P1 ECM connector, and the J2/P2 ECM connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the customer connector and the ECM connector that are associated with the diagnostic lamp. Refer to illustration 1.
Check the J61/P61 customer connector (allen head screw) for the proper torque of 2.25 0.25 N m (20 2 lb in).Check the ECM connector J1/P1 and J2/P2 for the proper torque of 6.0 N m (55 lb in).
Check the harness and wiring for abrasions and for pinch points from the battery to the ECM.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The connectors and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem with the electrical connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Verify the Negative Battery Connections
Locate the negative battery bus bars and verify that the connections are installed properly.Refer to Troubleshooting, "Engine Wiring Information" for additional information.Expected Result:The negative battery connections have been properly installed.Results:
Ok - The connections for the negative battery bus bar have been installed properly. Proceed to Test Step 3.
Not Ok - The connections for the negative battery bus bar have not been installed properly.Repair: Make the necessary connections in order to ensure proper installation. Proceed to Test Step 3.Test Step 3. Check the Status of the Switch
Connect the electronic service tool to the service tool connector.
Turn the keyswitch to the ON position.
Monitor the status screen on the electronic service tool while each switch is cycled.Expected Result:Each switch is displayed as "ON" and "OFF" when the switch is cycled.Results:
OK - The switches are operating properly.STOP
Not OK - There is a problem with the wiring or the switch. Proceed to Test Step 4.Test Step 4. Install a Jumper at the Customer Connector and Check the Status of the Switch
Turn the keyswitch to the OFF position.
Fabricate a jumper wire that will reach from the negative battery bus bar to the J61 customer connector.
Install a 9W-0844 Connection Socket on one end of the jumper wire and a connector that will connect to the negative battery bus bar on the opposite end.
Connect the jumper wire from the negative battery bus bar to the pin for


Parts base EVINRUDE:

0511417
 
0511417 BASE ASSY.,Junction block
100990S, 115790S, 115890C, 150840S, 150940C, 175740S, 200640S
0511851
 
0511851 BASE ASSY.,Junction block
E100MLCSC, E115MLCIH, E115MLCSA, E140MLCIH, E140MLCSA, E150TRLCIA, E150TRLCSF, E175TRLCIM, E175TRLCSA, E200TRLCIB, E200TRLCSF, E235TRLCIB, E235TRLCSM, E70ELCIH, E70ELCSA, E75ERCIH, E75ERCSA, E85MLCSA, E90MLCIH
0511870
 
0511870 BASE, Junctin box
E115MLCIH, E115MLCNB, E115MLCTE, E140MLCIH, E140MLCNB, E140MLCTE, E150STLCTE, E150TRLCIA, E150TRLCNM, E150TRLCTB, E175TRLCIM, E175TRLCNB, E175TRLCTD, E200TRLCIB, E200TRLCNE, E200TRLCTD, E235STLCTS, E235TRLCIB, E235TRLCNE, E235TRLCTD, E70ELCIH, E70ELC
0325717
 
0325717 BASE, Air silencer
E115MLCIH, E115MLCNB, E115MLCTE, E140MLCIH, E140MLCNB, E140MLCTE, E90MLCIH, E90MLCNB, E90MLCTE
Back to top