0587010 EVINRUDE BASE & HARNESS ASSEMBLY


0587010 BASE & HARNESS ASSEMBLY EVINRUDE DE150CXAAA, DE150CXAAC, DE150CXINS, DE150PXAAA, DE150PXAAC, DE150PXINS, DE200CXAAA, DE200CXAAC, DE200PXAAA, DE200PXAAC, E135DHLAAB, E135DHXAAC, E135HCXAAC, E135HSLAAB, E150DBXAAA, E150DBXAAC, E150DBXIIB, E150DBXINE, E150DBXISF, E150DBXSEA, E150DCXAAA BASE
0587010 BASE & HARNESS ASSEMBLY EVINRUDE
Rating:
48

Buy BASE & HARNESS ASSEMBLY 0587010 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

BRP EVINRUDE entire parts catalog list:

DE150CXAAA, DE150CXAAB 2012
DE150CXAAC 2012
DE150CXINS 2012
DE150PXAAA, DE150PXAAB 2012
DE150PXAAC 2012
DE150PXINS 2012
DE200CXAAA, DE200CXAAB 2012
DE200CXAAC 2012
DE200PXAAA, DE200PXAAB 2012
DE200PXAAC 2012
E135DHLAAB 2012
E135DHXAAC 2012
E135HCXAAC 2012
E135HSLAAB 2012
E150DBXAAA, E150DBXAAB 2012
E150DBXAAC 2012
E150DBXIIB 2011
E150DBXINE 2012
E150DBXISF, E150DBXISM 2010
E150DBXSEA 2009
E150DCXAAA, E150DCXAAB 2012
E150DCXAAC 2012
E150DCXIIB 2011
E150DCXINE 2012
E150DCXISF, E150DCXISM 2010
E150DCXSEA 2009
E150DHLAAA, E150DHLAAB 2012
E150DHLIIB 2011
E150DHLINE 2012
E150DHLISF, E150DHLISM 2010
E150DHLSEA 2009
E150DPLAAA, E150DPLAAB 2012
E150DPLIIB 2011
E150DPLINE 2012
E150DPLISF, E150DPLISM 2010
E150DPLSEA 2009
E150DPXAAA, E150DPXAAB 2012
E150DPXAAC 2012
E150DPXIIB 2011
E150DPXINE 2012
E150DPXISF, E150DPXISM 2010
E150DPXSEA 2009
E150DSLAAA, E150DSLAAB 2012
E150DSLIIB 2011
E150DSLINE 2012
E150DSLISF, E150DSLISM 2010
E150DSLSEA 2009
E150HGLSES 2009
E150HGXSES 2009
E150HSLAAA, E150HSLAAB 2012
E150HSLIIA 2011
E150HSLINM 2012
E150HSLISF, E150HSLISR 2010
E150HSLSEC 2009
E175DCXAAA, E175DCXAAB 2012
E175DCXAAC 2012
E175DCXIIB 2011
E175DCXINE 2012
E175DCXISF, E175DCXISM 2010
E175DCXSEA 2009
E175DMXAAA, E175DMXAAB 2012
E175DMXAAC 2012
E175DPLAAA, E175DPLAAB 2012
E175DPLIIB 2011
E175DPLINE 2012
E175DPLISF, E175DPLISM 2010
E175DPLSEA 2009
E175DPXAAA, E175DPXAAB 2012
E175DPXAAC 2012
E175DPXIIB 2011
E175DPXINE 2012
E175DPXISF, E175DPXISM 2010
E175DPXSEA 2009
E175DSLAAA, E175DSLAAB 2012
E175DSLIIB 2011
E175DSLINE 2012
E175DSLISF, E175DSLISM 2010
E175DSLSEA 2009
E200DCXAAA, E200DCXAAB 2012
E200DCXAAC 2012
E200DCXISB, E200DCXISF 2010
E200DCXSEM 2009
E200DPLAAA, E200DPLAAB 2012
E200DPLISB, E200DPLISF 2010
E200DPLSEM 2009
E200DPXAAA, E200DPXAAB 2012
E200DPXAAC 2012
E200DPXISB, E200DPXISF 2010
E200DPXSEM 2009
E200DSLAAA, E200DSLAAB 2012
E200DSLISB, E200DSLISF 2010
E200DSLSEM 2009

Information:

1. Remove nuts (1), cover (2), and the gasket. 2. Put No. 1 piston at the top center compression position (TDC) with the following procedure:a. Remove plug (3), two bolts and cover (2) from the flywheel housing. b. Install tool (B) in the flywheel housing. Use tool (B) to slowly rotate the engine in the direction of normal rotation, (counterclockwise as seen from the flywheel end of the engine), until timing bolt (4) can be installed in the flywheel housing and into the hole in the flywheel. c. Remove the valve cover from the valve cover base. Check to see if both rocker arms (5) for the No. 1 cylinder can be moved backward and forward. The No. 1 piston is at the top center compression position (TDC) when the timing bolt is installed in the flywheel and both rocker arms for the No. 1 cylinder can be moved backward and forward. If both rocker arms cannot be moved, the No. 1 piston is not at the top center compression position (TDC). Remove the timing bolt from the flywheel and rotate the engine in the direction of normal rotation, (counterclockwise as seen from the flywheel end of the engine one full turn 360°, and install the timing bolt again.3. Remove the timing bolt, and use tool (B) to rotate the engine in the opposite direction of normal rotation (clockwise as seen from the flywheel end of the engine) a minimum of 30°. The timing is correct if tool (A) and the timing bolt can be installed at the same time. The timing procedure in the Testing and Adjustment Manual must be done again if the timing bolt and tool (A) can not be installed at the same time.4. Remove the plug from the timing pin hole in the fuel injection pump housing, and install tool (A) in the timing pin hole. 5. Remove eight bolts (6) and automatic timing advance (7). 6. Remove gear (9) from fuel injection pump camshaft (8).The following steps are for the installation procedure.7. Install gear (9) on fuel injection pump camshaft (8). 8. Install two 3/8 in. - 16 NC × 6 in. (152.4 mm) long guide bolts (10). Space the guide bolts evenly.
There is a light spring located beneath the flyweight cover (12). Hold cover (12) while removing last nut (11). Slowly remove flyweight cover (12) to avoid dropping the spring.
9. Remove four nuts (11) and remove flyweight cover (12). 10. Put automatic timing advance (13) in position on the fuel injection pump camshaft, and install four bolts (14). Tighten bolts (14) just past finger tight. Remove guide bolts (15). 11. Install four nuts (16) standard torque. Install tool (C). 12. Tighten four knurled nuts (17) finger tight.
Do not use any tools to tighten the knurled nuts.
13. Install all mounting bolts (14) and tighten to a torque of 3 N m (27 lb.in.).14. Loosen knurled nuts (17). Remove four nuts (16) and remove tool (C).15. Install the spring and flyweight cover (12). Install four nuts (16).16. Install a gasket and timing advance cover (2). Tighten eight nuts (1) to standard torque.17. Remove timing pin (A) and replace the plug in the fuel pump housing.18. Remove timing bolt (4) and replace the plug. Install cover (2) on the flywheel housing.19. Check the dynamic timing curve. See Testing and Adjusting for the proper specifications.Disassemble Automatic Timing Advance
Start By:a. remove automatic timing advance 1. Remove four nuts (1) and remove retainer (2) from automatic timing advance. 2. Remove spring (3) and race (4). 3. Remove four capscrews (5), two retainer plates (6) and remove carrier group (7) from automatic timing advance. 4. Remove snap ring (7), tapered race (9), spool (10) and weights (11) from carrier (7). 5. Remove race (12) from carrier (7). 6. Remove four bolts (13). 7. Remove plate (14), ring (16) and ring (17) from carrier assembly (15). Remove seals (19) and (20) from carrier assembly (15). Remove seal (18) from plate (14).Assemble Automatic Timing Advance
1. Install new seals (18), (19) and (20). 2. Lubricate seal (18), (19) and (20) with engine oil then carefully install carrier assembly (15) into ring (17). Install ring (16) and plate (14). 3. Align proper bolt holes and install four bolts (13). 4. Position race (12) into carrier (7).5. Position weights (11), spool (10), tapered race (9) and snap ring (7) into carrier (7). 6. Lubricate spool (10) and lower it into position in the automatic timing advance. Position retainer plates (6) and install four capscrews (5). Tighten capscrews (5) to a torque of 3.4 0.4 N m (30 4 lb.in.). 7. Position race (4) and spring (3). When installing retainer (2), be sure spring (3) properly engages retainer adjustment screw.8. Position retainer (2) and install four nuts (1)End By:a. install automatic timing advance


Parts base EVINRUDE:

0351751
*BASE, Flywheel cover
0351751 *BASE, Flywheel cover
DE150CXAAA, DE150CXAAC, DE150CXINS, DE150PXAAA, DE150PXAAC, DE150PXINS, DE200CXAAA, DE200CXAAC, DE200PXAAA, DE200PXAAC, E115DBXAAA, E115DBXABA, E115DBXIIB, E115DBXINE, E115DBXISF, E115DBXSCR, E115DBXSEF, E115DBXSUC, E115DCXAAA, E115DCXABA, E115DCXIIA
Back to top