0375761 BEARING, Roller, prop. shaft EVINRUDE
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
BEARING
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- GEARCASE GROUP » 0375761
33902A, 33903A, 33952A, 33953A 1969
40002A, 40003A 1970
40052A, 40053A 1970
40072A, 40073A 1970
40102B, 40102G, 40103B, 40103G, 40152B, 40152G, 40153B, 40153G 1971
40802A, 40802D, 40802S, 40803A, 40803D, 40803S 1968
40852A, 40852C, 40852D, 40852S, 40853A, 40853C, 40853D, 40853S 1968
40872A, 40872C, 40872D, 40873A, 40873C, 40873D 1968
40902R, 40903R 1969
40952R, 40953R 1969
40972R, 40973R 1969
Information:
Note: 372-5260 Kit-Test and 441-0451 Kit-Test are required for completing this procedure.Recommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Check the Diesel Exhaust Fluid (DEF) quality..
A. Measure the DEF quality. Refer to Testing and Adjusting, "Diesel Exhaust Fluid Quality - Test" for the procedure.
DEF Quality
Result : The DEF is not contaminated and the concentration is within the acceptable range.
Proceed to Test Step 2.
Result : The DEF is not contaminated and the concentration is not within the acceptable range.
Repair: Drain the DEF from the tank. Refill the tank with DEF that meets ISO 22241 quality standards.
Proceed to Test Step 6.
Result : The DEF is contaminated.
Repair : Contact the Dealer Solutions Network (DSN) for further information.
2. Perform the "DEF Dosing System Accuracy Test" using Cat® Electronic Technician (ET).
A. Refer to Testing and Adjusting, "Aftertreatment SCR System Dosing -Test" for the procedure.
DEF Dosing System Accuracy Test
Result : The quantity collected is below specification.
Proceed to Test Step 3.
Result : The quantity collected is within specifications.
Repair: Install the DEF injector. Refer to Disassembly and Assembly, DEF Injector and Mounting - Remove and Install.
Proceed to Test Step 6.
Result : The quantity collected is above specification. A failed DEF injector has been detected.
Repair : Replace the DEF injector. Refer to Disassembly and Assembly, DEF Injector and Mounting - Remove and Install.
Proceed to Test Step 5.
3. Check the DEF pressure line.
A. Turn the keyswitch to OFF. Allow 2 minutes to elapse before proceeding.
B. Visually inspect the lines for leaks or damage.
C. Remove the DEF pressure line between the DEF pump and the DEF injector.
D. Inspect the DEF pressure line for obstructions. Flush the line with water or low-pressure air, if necessary.
Note : Possible obstructions are ice, DEF deposits, or debris.
Restriction, Obstructions, and Leaks
Result : An obstruction was found.
Repair : Flush or replace the line.
Proceed to Test Step 5.
Result : An obstruction was not found.
Proceed to Test Step 4.
4. Replace the DEF injector.
A. Turn the keyswitch to OFF.
B. Replace the DEF injector. Refer to Disassembly and Assembly, DEF Injector and Mounting - Remove and Install.
Note : Do not install the new injector until Test Step 5 has been completed.
DEF Injector
Result: The DEF injector was connected to the DEF pressure line and the electrical connector.
Proceed to Test Step 5.
5. Perform the "DEF Dosing System Accuracy Test" using Cat ET
A. Perform a "DEF Dosing System Accuracy Test" using Cat ET. Refer to Testing and Adjusting, "Aftertreatment SCR System Dosing Test" for the procedure.
"DEF Dosing System Accuracy Test"
Result: The quantity collected is within specification. Install the DEF injector.
Proceed to Test Step 6.
Result: The quantity collected is not within specifications.
Repair : Replace the DEF pump. Refer to Disassembly and Assembly, Diesel Exhaust Fluid Pump - Remove and Install. Reinstall the DEF injector.
Proceed to Test Step 6.
6. Perform an "Aftertreatment System Functional Test"
A. Turn the keyswitch to ON.
B. Connect to Cat ET.
C. Perform an "Aftertreatment System Functional Test" using Cat ET.
D. Download a warranty report. Refer to "Aftertreatment Abnormal Shutdown History" under the "Information" tab in the "Engine #1 Aftertreatment Controller".
Note : If hot shutdowns have occurred, allow the engine to cool down before shutting the machine OFF.
"Aftertreatment System Functional Test"
Result : The test was successful.
Return the unit to service.
Result : The test not was successful and more codes were logged.
Repair : Troubleshoot the additional codes, refer to theTroubleshooting manual for the correct procedure.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Table 2
Troubleshooting Test Steps Values Results
1. Check the Diesel Exhaust Fluid (DEF) quality..
A. Measure the DEF quality. Refer to Testing and Adjusting, "Diesel Exhaust Fluid Quality - Test" for the procedure.
DEF Quality
Result : The DEF is not contaminated and the concentration is within the acceptable range.
Proceed to Test Step 2.
Result : The DEF is not contaminated and the concentration is not within the acceptable range.
Repair: Drain the DEF from the tank. Refill the tank with DEF that meets ISO 22241 quality standards.
Proceed to Test Step 6.
Result : The DEF is contaminated.
Repair : Contact the Dealer Solutions Network (DSN) for further information.
2. Perform the "DEF Dosing System Accuracy Test" using Cat® Electronic Technician (ET).
A. Refer to Testing and Adjusting, "Aftertreatment SCR System Dosing -Test" for the procedure.
DEF Dosing System Accuracy Test
Result : The quantity collected is below specification.
Proceed to Test Step 3.
Result : The quantity collected is within specifications.
Repair: Install the DEF injector. Refer to Disassembly and Assembly, DEF Injector and Mounting - Remove and Install.
Proceed to Test Step 6.
Result : The quantity collected is above specification. A failed DEF injector has been detected.
Repair : Replace the DEF injector. Refer to Disassembly and Assembly, DEF Injector and Mounting - Remove and Install.
Proceed to Test Step 5.
3. Check the DEF pressure line.
A. Turn the keyswitch to OFF. Allow 2 minutes to elapse before proceeding.
B. Visually inspect the lines for leaks or damage.
C. Remove the DEF pressure line between the DEF pump and the DEF injector.
D. Inspect the DEF pressure line for obstructions. Flush the line with water or low-pressure air, if necessary.
Note : Possible obstructions are ice, DEF deposits, or debris.
Restriction, Obstructions, and Leaks
Result : An obstruction was found.
Repair : Flush or replace the line.
Proceed to Test Step 5.
Result : An obstruction was not found.
Proceed to Test Step 4.
4. Replace the DEF injector.
A. Turn the keyswitch to OFF.
B. Replace the DEF injector. Refer to Disassembly and Assembly, DEF Injector and Mounting - Remove and Install.
Note : Do not install the new injector until Test Step 5 has been completed.
DEF Injector
Result: The DEF injector was connected to the DEF pressure line and the electrical connector.
Proceed to Test Step 5.
5. Perform the "DEF Dosing System Accuracy Test" using Cat ET
A. Perform a "DEF Dosing System Accuracy Test" using Cat ET. Refer to Testing and Adjusting, "Aftertreatment SCR System Dosing Test" for the procedure.
"DEF Dosing System Accuracy Test"
Result: The quantity collected is within specification. Install the DEF injector.
Proceed to Test Step 6.
Result: The quantity collected is not within specifications.
Repair : Replace the DEF pump. Refer to Disassembly and Assembly, Diesel Exhaust Fluid Pump - Remove and Install. Reinstall the DEF injector.
Proceed to Test Step 6.
6. Perform an "Aftertreatment System Functional Test"
A. Turn the keyswitch to ON.
B. Connect to Cat ET.
C. Perform an "Aftertreatment System Functional Test" using Cat ET.
D. Download a warranty report. Refer to "Aftertreatment Abnormal Shutdown History" under the "Information" tab in the "Engine #1 Aftertreatment Controller".
Note : If hot shutdowns have occurred, allow the engine to cool down before shutting the machine OFF.
"Aftertreatment System Functional Test"
Result : The test was successful.
Return the unit to service.
Result : The test not was successful and more codes were logged.
Repair : Troubleshoot the additional codes, refer to theTroubleshooting manual for the correct procedure.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Parts bearing EVINRUDE:
0378251
0378251 BEARING,Wrist pin
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 400
0378515
0378515 BEARING SET,Conn.rod
100193A, 100293R, 100882B, 115083D, 115393M, 115983E, 125183C, 125283R, 135383M, 33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, 50172S, 50202C, 50302R, 50442M, 55872A, 5
0375763
0375763 BEARING, Roller, lower
18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25902B, 33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
0378657
0378657 BEARING ASSEMBLY, Roller, upper
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
0378578
0378578 .BEARING, Drive shaft
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
0376856
0376856 .BEARING, Pinion, upper
25702H, 25802C, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 40072A, 40102B, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, BE20SEEDA, BE20SREDA, BE25AREDC, BE25BAEDR, BE25EEDM, BE30BAEDE, BE30EEDE, BE35AREDS, E15DHPLAAA, E15DHPLAAB, E15D
0376857
0376857 BEARING, Thrust, pinion
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA
0376858
0376858 BEARING, Pinion, lower
33002M, 33802M, 33902A, 40002A, 40052A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40902R, 40952R, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA