0378578 .BEARING, Drive shaft EVINRUDE
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
BEARING
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Compatible models:
BRP EVINRUDE entire parts catalog list:
- GEARCASE GROUP » 0378578
33902A, 33903A, 33952A, 33953A 1969
40002A, 40003A 1970
40052A, 40053A 1970
40072A, 40073A 1970
40102B, 40102G, 40103B, 40103G, 40152B, 40152G, 40153B, 40153G 1971
40202E, 40203E, 40252E, 40253E 1972
40304D, 40305D, 40354D, 40355D 1973
40802A, 40802D, 40802S, 40803A, 40803D, 40803S 1968
40852A, 40852C, 40852D, 40852S, 40853A, 40853C, 40853D, 40853S 1968
40872A, 40872C, 40872D, 40873A, 40873C, 40873D 1968
40902R, 40903R 1969
40952R, 40953R 1969
40972R, 40973R 1969
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 342-9516 Line Socket 1
B 4C-5597 Anti-Seize Compound -
C 195-4609 Seal Pick 1
D - Isopropyl Alcohol -
E 5P-4996 Plug 2 Start By:
Remove the Exhaust Elbow.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Turn the fuel supply to the OFF position and turn the power disconnect switch to the OFF.
Illustration 1 g02324314
Loosen clamp assembly (1).Note: Place locating marks on each tube assembly and the clamp assemblies prior to disassembly.
Remove bolt and clamp assembly (2).
Remove three bolts (4) and position tube assembly (3) out of the way.
Illustration 2 g02481317
Remove bolt (6) and the ground strap. Disconnect cable assembly (5).
Remove allen bolt (7), remove the hold down clamp, and disconnect cable assembly (7a).
Use Tooling (A) to disconnect the flame detection sensor (8).
Illustration 3 g02325353Note: Cap all tube assemblies and fittings that are disconnected to prevent fluid loss. This action will also keep contaminants out of the systems.
Disconnect tube assemblies (9) and (10).
Disconnect tube assemblies (11) and plug with Tooling (E).
Illustration 4 g02325434
Remove nuts (16) and remove combustion head (15).
Remove gasket (14), tube assembly (13), and gasket (12).Note: The gaskets are one time use only. Replace with new gaskets upon installation.
If required, remove studs (17).
Illustration 5 g02325454
Remove fittings (20) and (21).
Remove spark plug (19) and remove fittings (18).
Illustration 6 g02481319
Use Tooling (C) to remove O-ring seals (22) and (23) from cable assembly (7a). Discard the O-ring seals.Installation Procedure
Install combustion head (16) in reverse order of removal.
Apply Tooling (B) onto the threads of the studs (17). Tighten studs (17) to a torque of 17 2 N m (150 18 lb in).
Tighten nuts (16) in a crisscross pattern to a torque of 23 3 N m (17 2 lb ft). Tighten nuts (16) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft). Tighten nuts (16) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft).
Use caution when you are using isopropyl alcohol. Avoid prolonged skin contact with isopropyl alcohol.Vapors may be harmful if inhaled. Use only in a well ventilated area. Do not smoke while using isopropyl alcohol.Isopropyl alcohol is flammable. Do not use near an open flame or near welding operations. Keep isopropyl alcohol away from heated surfaces exceeding 482°C (900°F).
Note: This connection is an electrical connection and cannot be lubricated with a petroleum-based lubricant. Isopropyl alcohol is the only approved lubrication for this connection.
Lubricate new O-ring seals (22) and (23) with Tooling (D) prior to installation.
Tighten fittings (20) and (21) to a torque of 60 6 N m (44 4 lb ft).
Tighten fittings (18) to a torque of 30 2 N m (22 1 lb ft).
Tighten spark plug (19) to a torque of 57.5 4 N m (42 3 lb ft).
Apply Tooling (B) to the threads of flame detection temperature sensor (8) and install the sensor. Use Tooling (A) to tighten flame detection temperature sensor (8) to a torque of 45 5 N m (33 3 lb ft).
Check the coolant level. If necessary, refer to Operation and Maintenance Manual, "Coolant - Change" for the proper filling procedures.
Perform the ARD ignition test. Refer to Troubleshooting Manual, "ARD Ignition - Test".
Parts bearing EVINRUDE:
0378251
0378251 BEARING,Wrist pin
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 400
0378515
0378515 BEARING SET,Conn.rod
100193A, 100293R, 100882B, 115083D, 115393M, 115983E, 125183C, 125283R, 135383M, 33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, 50172S, 50202C, 50302R, 50442M, 55872A, 5
0375763
0375763 BEARING, Roller, lower
18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25902B, 33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
0378657
0378657 BEARING ASSEMBLY, Roller, upper
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
0376856
0376856 .BEARING, Pinion, upper
25702H, 25802C, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 40072A, 40102B, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, BE20SEEDA, BE20SREDA, BE25AREDC, BE25BAEDR, BE25EEDM, BE30BAEDE, BE30EEDE, BE35AREDS, E15DHPLAAA, E15DHPLAAB, E15D
0376857
0376857 BEARING, Thrust, pinion
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA
0376858
0376858 BEARING, Pinion, lower
33002M, 33802M, 33902A, 40002A, 40052A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40902R, 40952R, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA
0385173
0385173 BEARING, Ball, prop. shaft
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, 40202E, 40304D, 40404S, 40504C, 40604A, BE10EEDD, BE10RELEUS, BE15EEDS, BE15RELEUC, E10ECCD, E10ECDB, E10ECES, E10ECOM, E10ECSE, E10ECUE, E10EECC, E10EEIR, E10EENA, E10EEOE, E10E