5032316 EVINRUDE BEARING SET, Crankshaft, 0.25mm U.S.


5032316 BEARING SET, Crankshaft, 0.25mm U.S. EVINRUDE E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS BEARING
5032316 BEARING SET, Crankshaft, 0.25mm U.S. EVINRUDE
Rating:
88

Buy BEARING SET, Crankshaft, 0.25mm U.S. 5032316 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
£39.44
 

18-09-2017
4.41[1.80] pounds
Connected : Connected Essentials
Connected Essentials 5032316 Tailored Heavy Duty Custom Fit Car Mats, for Seat Leon Oval Clips (2002-2005), Grey with Blue Trim, Premium
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Seat Leon Oval Clips (2002-2005)||Supplied with clips (as applicable) for security||Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear||Manufactured from 650gram automotive quality carpet - for strength and durability||Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Number on catalog scheme: 9
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E25EL4SIC, E25PL4SIC, E25R4SIC, E25RL4SIC, E25TE4SIC, E25TEL4SIC 2001
E25EL4SSS, E25PL4SSS, E25R4SSS, E25RL4SSS, E25TE4SSS, E25TEL4SSS 2000
E30EL4SIC, E30PL4SIC, E30R4SIC, E30RL4SIC, E30TE4SIC, E30TEL4SIC 2001
E30EL4SSS, E30PL4SSS, E30R4SSS, E30RL4SSS, E30TE4SSS, E30TEL4SSS 2000

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6192 Pliers 1
B 7M-3978(1) Piston Ring Expander Gp 1
7B-7974(2) Piston Ring Expander Gp 1
C 5P-8639 Hydraulic Press (Connecting Rod Bearing) 1
8F-0024 Hose Assembly 1
1P-2375 Connecting Coupler 1
1P-2376 Connecting Coupler 1
5P-8651 Spacer 1
5P-8649 Adapter 1
5P-8650 Bushing Adapter 1
9U-6600 Hand Hydraulic Pump 1
(1) For use with 137 mm (5.4 inch) bores.
(2) For use with 145 mm (5.7 inch) bores.Note: Prior to removal from the engine, the pistons and connecting rod assemblies were marked. The components must be reassembled together. The components must be installed in the original location in the engine. Do not interchange any of the components.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01017742
Illustration 2 g01018268
The connecting rod must be heated for the installation of the piston pin bearing. Do not use a torch.
Raise heat of connecting rod (6) along Length (Y). (Y) Maximum Length for heating the connecting rod ... 95 mm (3.7 inch)
Allow the connecting rod and the bearing to cool to room temperature.
Use Tooling (C) to remove the old bearing and install new bearing (7) at the same time. The adapter of Tooling (C) should make full contact with the surfaces of connecting rod (6). Note: Orient the bearing joint within 5 degrees of either Location (X).
Use a pin boring machine to machine the bore of bearing (7) to the correct diameter. Diameter of bearing bore ... 60.035 0.008 mm (2.3636 0.0003 inch)
Illustration 3 g01056145
Position the spring for the oil control piston ring in the oil ring groove in the piston body assembly.
Position oil control piston ring (3) over the spring. Position the oil control piston ring so that the gap is 180 degrees from the joint in the spring. Install the oil control piston ring on the piston with Tooling (B).
Use Tooling (B) to install intermediate piston ring (2) with the side that has the identification “UP-2” toward the top of the piston.
Use Tooling (B) to install top piston ring (1) with the side that has the identification “UP-1” toward the top of the piston.
Position piston rings (1), (2), and (3) so the gaps are 120 degrees from each other.
Check the clearance between the ends of piston rings (1), (2), and (3). Refer to Specifications, "Pistons And Rings".
Position piston body assembly (4) on connecting rod (6). Apply clean engine oil to connecting rod pin (8) and install the connecting rod pin. Install pin retainer (5) with Tooling (A).
Install upper connecting rod bearing (9) in connecting rod (6). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod.
Install lower connecting rod bearing (10) in connecting rod bearing cap (11). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod bearing cap.
Ensure that the dowels are installed in the connecting rod bearing cap. End By:
Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".


Parts bearing EVINRUDE:

5032315
 
5032315 BEARING, Connecting rod, 0.25mm U.S.
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031934
BEARING, Connecting rod
5031934 BEARING, Connecting rod
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031937
BEARING SET, Crankshaft, green
5031937 BEARING SET, Crankshaft, green
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5032317
BEARING SET, Crankshaft, 0.50mm U. S.
5032317 BEARING SET, Crankshaft, 0.50mm U. S.
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031939
BEARING SET, Crankshaft, no paint
5031939 BEARING SET, Crankshaft, no paint
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031941
BEARING SET, Crankshaft, blue
5031941 BEARING SET, Crankshaft, blue
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031940
BEARING SET, Crankshaft, yellow
5031940 BEARING SET, Crankshaft, yellow
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031938
BEARING SET, Crankshaft, black
5031938 BEARING SET, Crankshaft, black
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
Back to top