5041318 EVINRUDE BELT GUIDE


5041318 BELT GUIDE EVINRUDE B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, E10EL4AAB, E10EL4INS, E10PL4INS, E10TEL4AAB BELT
5041318 BELT GUIDE EVINRUDE
Rating:
43

Buy BELT GUIDE 5041318 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

BRP EVINRUDE entire parts catalog list:

B10EL4AAA, E10EL4AAA 2012
B10EL4AAB 2012
B10EL4INS 2012
B10PL4AAA, B10PX4AAA, E10PL4AAA, E10PX4AAA 2012
B10PL4AAB, B10PX4AAB, E10PL4AAB, E10PX4AAB 2012
B10PL4INS 2012
B10PX4INS, E10PX4INS 2012
B10R4AAA, B10RL4AAA, E10R4AAA, E10RL4AAA 2012
B10R4AAB, B10RL4AAB, B10TEL4AAB, E10R4AAB, E10RL4AAB 2012
B10RL4INS, E10RL4INS 2012
B10TEL4AAA, E10TEL4AAA 2012
B10TEL4INS, E10TEL4INS 2012
B10TPL4AAA, B10TPX4AAA, E10TPL4AAA, E10TPX4AAA 2012
B10TPL4AAB, B10TPX4AAB, E10TPL4AAB, E10TPX4AAB 2012
B10TPL4INS, E10TPL4INS 2012
B10TPX4INS, E10TPX4INS 2012
E10EL4AAB 2012
E10EL4INS 2012
E10PL4INS 2012
E10TEL4AAB 2012

Information:

3. Loosen the clamps on breather tube (1) and pull it back for clearance. 4. Remove bolt (2) from the cover on the side of the cylinder block. 5. Remove the three bolts that hold cover (3) to the water pump. Remove cover (3) from the water pump. 6. Remove the two bolts, and remove elbow (4) from bonnet (5). Remove the two bolts, and remove bonnet (5) from the water pump. It is not necessary to remove bolts (6). These bolts only hold the cover to the timing gear cover.7. Remove six long bolts (7) that hold the water pump to the timing gear cover. Remove water pump (8).Install Water Pump
1. Check the O-ring seals and gaskets, and make replacements if needed. 2. Make sure O-ring seal (9) is in position on the water pump. Put water pump (8) into position in the timing gear cover. Install the bolts that hold the water pump in place. 3. Make sure the gaskets are in place. Connect bonnet (5) to the water pump. Connect elbow (4) to the bonnet. 4. Make sure O-ring seal (10) is in position, and install cover (3) on the water pump. 5. Install bolt (2) on the cover on the side of the engine. 6. Put breather tube (1) in position, and install the clamps that hold it.7. Install the alternator mounting group and alternator on the engine.8. Install the water temperature regulator and manifold. See the topic Install Water Temperature Regulator and Manifold.9. Fill cooling system to the correct level. See the Maintenance Guide.Disassemble And Assemble Water Pump
Start By: The water pump seal can be replaced without removing the water pump from the engine.An intermittent leakage of a small amount of coolant from the hole in the water pump housing is not and indication of a water pump seal failure. This is required to provide lubrication for the seal. Replace the water pump seal only if a large amount of leakage or a constant flow of coolant is observed draining from the water pump housing. 1. Remove O-ring seal (3) from adapter (4). Remove the adapter from housing (7). Remove the O-ring seal from the outside of the adapter.2. Remove bolt (1) an washer (2). Use tooling (A) to remove impeller (6) from shaft (13).3. Remove spring and seal (5) from the shaft.4. Remove four bolts (16) from retainer (12) that hold the shaft assembly to the pump housing. Remove O-ring seal (18) from housing (7).5. Remove gear and shaft assembly (17) from the housing. Remove bolt (15), retainer (14), and retainer (12) from the shaft assembly.6. Use a press to remove shaft (13) from the gear. Remove bearing (9), spacer (10), and bearing (11) from the shaft.7. Remove lip-type seal (8) from the housing.8. Turn the housing over, and remove ceramic ring (20) and seal (19) from the housing. The following steps are for the assembly of the water pump.9. Use 6V1541 Quick Cure Primer and clean shaft (13) and the seal counter bore in the pump housing.10. Install bearing (9), spacer (10), and bearing (11) on shaft (13).11. Put seating (12) and gear (17) on the shaft assembly. Install retainer (14) and bolt (15) on the shaft.12. Use tooling (B) to install lip-type seal (8) in housing (7). Install seal with the lip toward the inside of the housing. Put a small amount of clean engine oil on the lip of the seal.13. Install a new O-ring seal (18) on the housing.14. Put gear and shaft assembly (17) in position in the housing. Install bolt (16) that hold retainer (12) to the housing.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
15. Put ceramic ring (20) in position in seal (19). Use hand pressure and tool (C) to install the ceramic ring in the housing.
Avoid contaminating the seal faces with grease or oil. Also, avoid stretching the rubber seal during installation.
The carbon seal assembly must rotate with the water pump shaft after installation.16. Separate spring from seal (5). Use hand pressure and tool (C) to install the seal on the shaft of gear and shaft assembly (17). Push the seal on the shaft until the seal faces make light contact. Install the spring on the shaft.17. Put impeller (6) in position on the shaft. Install washer (2) and bolt (1) that hold the impeller. Tighten the bolt to a torque of 39 3 N*m (29 2 lb.ft.).18. Install the O-ring seal on the outside diameter of adapter (4). Put a small amount of clean SAE 30 oil on the O-ring seal.19. Install O-ring seal (3) on the adapter.20. Put adapter (4) in position on the housing.End By:a. install water pump


Parts belt EVINRUDE:

5041303
 
5041303 BELT COVER
B10R4AAA, B10R4INS, B10RL4INS
Back to top