0328010 EVINRUDE BOLT, Tilting shaft


0328010 BOLT, Tilting shaft EVINRUDE E20CREND, E25REND, E25RSA, E25RSLS, E25RWCDC, E25RWCOS, E25RWCRD, E25RWCUR, E25RWEIM, E25RWENB, E25RWESA, E25RWK, E30RENR, E35RENR, U25RWA BOLT
0328010 BOLT, Tilting shaft EVINRUDE
Rating:
88

Buy BOLT, Tilting shaft 0328010 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 54
 

BRP EVINRUDE entire parts catalog list:

E20CREND, E20CRLEND, TE20CREND, TE20CRLEND 1992
E25REND, E25RLEND 1992
E25RSA, E25RSLA, E25RWCIM, E25RWLCIM 1981
E25RSLS, E25RSS, E25RWCTE, E25RWLCTE 1983
E25RWCDC, E25RWLCDC 1986
E25RWCOS, E25RWLCOS 1985
E25RWCRD, E25RWLCRD 1984
E25RWCUR, E25RWLCUR 1987
E25RWEIM, E25RWLEIM 1991
E25RWENB, E25RWLENB 1992
E25RWESA, E25RWLESA 1990
E25RWK, E25RWLK 1989
E30RENR, E30RLENR 1992
E35RENR, E35RLENR 1992
U25RWA, U25RWLA 1988

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 8H-0663 Bearing Puller 1
5F-7345 Puller 1
126-7183 Crossblock 1
126-7177 Puller Leg 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Remove the auxiliary equipment from the accessory drive housing. Refer to the Original Equipment Manufacture (OEM) for the correct procedure.
Illustration 1 g03360850
If the OEM driven equipment has not been installed to the auxiliary drive, remove bolts (1). Remove cover plate (2) and remove O-ring seal (3) (not shown).
Illustration 2 g03431636
Remove circlip (9) from housing (4).
Remove gear assembly (6) from housing (4).
If necessary, follow Step 5.a through Step 5.c in order to disassemble gear assembly (6).
Remove circlip (8) from gear assembly (6).
Use Tooling (A) in order to remove bearing (7) from gear (6).
Use a suitable tool in order to remove bearing (5) from housing (4). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 7M-7456 Bearing Mount Compound -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g03431639
Apply a small continuous bead of Tooling (B) to outer Surface (X) of bearing (5).
Use a suitable tool in order to install bearing (5) to housing (4). Remove any excess bearing mount compound.
Illustration 4 g03431658
Illustration 5 g03431659
If necessary, follow Step 3.a through Step 3.g in order to assemble bearing (7) onto gear (6).
Inspect the condition of the teeth and the splines of gear (6) for wear and damage. Inspect bearing (7) circlip (8) and circlip (9).
Inspect the bore in housing (4) for damage. If necessary, replace the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" and Disassembly and Assembly, "Housing (Front) - Install" for the correct procedure.
Apply a small continuous bead of Tooling (B) to inner Surface (Y) of bearing (7). Place the inner race of bearing (7) onto a suitable support. Press the shaft of gear (6) into bearing (7) until the shoulder of the gear is against the bearing. Remove any excess bearing mount compound.
Install circlip (8) into the groove in gear (6).
Apply a small continuous bead of Tooling (B) to the outer Surface (Z) of bearing (7).
Install gear assembly (6) to housing (4). Ensure that the shaft of gear (6) is correctly aligned with the bearing in housing (4). Remove any excess bearing mount compound.
Install circlip (9) into the groove in accessory drive housing (4). Ensure that circlip (9) is correctly positioned in the groove.
Ensure that there is tactile backlash between the idler gear and the accessory drive gear.
Illustration 6 g03360850
Install the auxiliary equipment to the accessory drive housing. Refer to the OEM for the correct procedure.
If the OEM driven equipment is not being installed to the auxiliary drive. Install a new O-ring seal (3) (not shown) and cover plate (2). Install bolts (1) and tighten the bolts to a torque of 44 N m (33 lb ft).


Back to top