0342605 EVINRUDE BOLT, Mounting


0342605 BOLT, Mounting EVINRUDE E40JREOS BOLT

Buy BOLT, Mounting 0342605 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 26
 

Compatible models:

E40JREOS   EVINRUDE

BRP EVINRUDE entire parts catalog list:

E40JREOS 1995

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     138-7575     Link Bracket     2    
B     9B-7237     Bolt     7    
C     8T-4896     Hard Washer     7    
D     189-0411     Shackle As     2    
E     8S-9906     Ratchet Puller     2    
F     -     Steel Beam (2 by 2 by 66 inch)     1    
G     -     Hardwood Block (4 by 4 by 12 inch)     2    
H     6V-3145     Load Leveling Beam     1    Start By:
Remove the hydraulic fan motor. Refer to Disassembly and Assembly, "Hydraulic Fan Motor - Remove and Install".
Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
Remove the Belt. Refer to Disassembly and Assembly, "Belt - Remove and Install".
At operating temperature, the hydraulic oil is hot and under pressure. Hot oils can cause burns.To prevent possible personal injury, release the pressure in the implement hydraulic circuit (boom, stick, bucket, and swing), travel circuits, and the hydraulic oil tank at the filler cap before any hydraulic lines or components are disconnected or removed.Remove the filler cap only when the engine is stopped and the filler cap is cool enough to touch.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00841042
Turn the battery disconnect switch to the OFF position.
Illustration 2 g00841220
Close the fuel shut off valve.
Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release" in the machine systems.
Drain the oil from the engine into a suitable container for storage or disposal. The refill capacity of the engine is 64.6 L (17 US gal).
At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Check the coolant level only after the engine has been stopped and the filler cap is cool enough to touch with the bare hand.Remove the filler cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with skin and eyes to prevent personal injury.
Drain the coolant from the cooling system into a suitable container for storage or disposal. The capacity of the cooling system is 101 L (26.7 US gal).Note: Remove any tie straps that need to be removed. Mark the locations for the tie straps. It is important to place all components in the original position.Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.Note: Put orientation and location marks on all fittings for installation purposes.Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.
Illustration 3 g00841231
Disconnect tube assembly (1) .


Parts bolt EVINRUDE:

0319590
 
0319590 BOLT, Throttle lever retainer
BE130TLECE, BE130TLEDM, BE130TLEUB, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, BE250CXECB, BE250CXEDA, BE250CXEUM, BE40EECR, BE40EEDS, BE40EEUC, BE50BEEDS, BE50ESECC, BE50RLEUC, C155WTLM, DE150CXAAA, DE150CXAAC, DE150CXIN
0336870
 
0336870 BOLT, Intake to hsg
B25JREUR, BE115GLECM, BE115TLEDA, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE20SRECB, BE20SREUM, BE25BAECM, BE30BAECS, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, BE40EEDS, BE40EEUC, BE50BEEDS, BE50RLEUC, BE90SLECM, E10
0336871
 
0336871 BOLT, Pin, gate
B25JREUR, BE115GLECM, BE115TLEDA, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE20SRECB, BE20SREUM, BE25BAECM, BE30BAECS, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, BE40EEDS, BE40EEUC, BE50BEEDS, BE50RLEUC, BE90SLECM, E10
0336930
 
0336930 BOLT, Brg. hsg
BE40EEDS, BE40EEUC, BE50BEEDS, BE50RLEUC, E40EEIA, E40EENJ, E40EEOD, E40EERE, E40EETB, E40JRECA, E40JREDC, E40JREOS, E40JREUR, E50BEEIA, E50BEENJ, E50BEEOD, E50BEERE, E50BEETB
0336934
 
0336934 BOLT, Pump adaptor
BE40EEDS, BE40EEUC, BE50BEEDS, BE50RLEUC, E40EEIA, E40EENJ, E40EEOD, E40EERE, E40EETB, E40JRECA, E40JREDC, E40JREOS, E40JREUR, E50BEEIA, E50BEENJ, E50BEEOD, E50BEERE, E50BEETB
0342356
 
0342356 BOLT, Liner to intake
B25JREUR, BE20SRECB, BE20SREUM, BE25BAECM, BE30BAECS, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, E25JREDC, E25JREOS, E40JREDC, E40JREOS, E40JREUR, SE25RDEEM, SE25RDSIE, SE25RDSSB
0342614
 
0342614 BOLT
E40JREOS
Back to top