5030388 EVINRUDE BOLT


5030388 BOLT EVINRUDE E70, E70FLTLECS, E70PL4EEC, E70PL4SIA BOLT
5030388 BOLT EVINRUDE
Rating:
98

Buy BOLT 5030388 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 42
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E70, E70PL4SSR 2000
E70FLTLECS 1998
E70PL4EEC 1999
E70PL4SIA 2001

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     370-8376     Cap Kit     1    
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Remove the fuel injection lines.
Illustration 1 g02484242
Illustration 2 g02484286
Thoroughly clean the area around fuel manifold (1) .
Disconnect harness assembly (4) from fuel pressure sensor (5) .
Remove banjo bolt (3) from plastic tube assembly (2). Use Tooling (A) to plug the plastic tube assembly Remove sealing washers (7) (not shown). Use Tooling (A) to plug fuel manifold (1) .
Remove bolts (6) .
Remove fuel manifold (1) from the cylinder block.
If necessary, remove fuel pressure relief valve (8) from fuel manifold (1). Ref to Disassembly and Assembly, "Relief Valve (Fuel)" for the correct procedure.Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that all ports on the fuel manifold are capped. Ensure that the fuel manifold is externally clean and free from damage.Note: Do not install a fuel manifold that has not been capped. All caps must be left in place until the fuel injection lines are installed.
Illustration 3 g02484242
Illustration 4 g02484286
If necessary, install fuel pressure relief valve (8) to fuel manifold (1). Refer to Disassembly and Assembly, "Relief Valve (Fuel)" for the correct procedure.
Position fuel manifold (1) onto the cylinder block. Install bolts (6) to fuel manifold (1) finger tight.
Install a new set of seals to the electronic unit injectors and a new set of fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines" for the correct procedure.
Tighten bolts (6) to a torque of 22 N m (195 lb in).
Install a new sealing washer (7) (not shown) to banjo bolt (3) .
Remove plug from plastic tube assembly (2). Install assembly of banjo bolt (3) to plastic tube assembly (2). Install remaining new sealing washer (7) (not shown) to banjo bolt (3) .
Install banjo bolt (3) and plastic tube assembly (2) to pressure relief valve (8) finger tight.
Tighten banjo bolts (3) to a torque of 15 N m (133 lb in).
Connect harness assembly (4) to fuel pressure sensor (5) .
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.


Parts bolt EVINRUDE:

5030989
 
5030989 BOLT, Plate
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030609
BOLT, Cylinder head
5030609 BOLT, Cylinder head
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030987
 
5030987 BOLT
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E50PL4EES, E50PL4EES, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030413
BOLT, Anode
5030413 BOLT, Anode
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030402
BOLT, Front, mount
5030402 BOLT, Front, mount
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5031121
 
5031121 BOLT, Bracket, cables
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030782
 
5030782 BOLT, Through
E70, E70FLTLECS, E70PL4EEC
5030873
BOLT, Reservoir
5030873 BOLT, Reservoir
E70, E70FLTLECS, E70PL4EEC
Back to top