0215287 *DECAL, "BOMBARDIER" F/R EVINRUDE
E100FPLSOC, E100FPLSRS, E115FPLSNF, E115FPLSOD, E115FPLSRE, E115FPLSTB, E115FPXSOD, E115FPXSRE, E135FCXSNF, E135FCXSOB, E135FCXSTA, E135FPLSOB, E135FPLSRM, E135FPLSTA, E135FPXSOB, E135FPXSRM, E135FSLSTA, E135FSLSTF, E150FCXSNF, E150FCXSOC, E150FCXSRS
DECAL
Price: query
Rating:
Compatible models:
E100FPLSOC
E100FPLSRS
E115FPLSNF
E115FPLSOD
E115FPLSRE
E115FPLSTB
E115FPXSOD
E115FPXSRE
E135FCXSNF
E135FCXSOB
E135FCXSTA
E135FPLSOB
E135FPLSRM
E135FPLSTA
E135FPXSOB
E135FPXSRM
E135FSLSTA
E135FSLSTF
E150FCXSNF
E150FCXSOC
E150FCXSRS
E150FCXSTD
E150FHLSOC
E150FHLSRS
E150FPLSOC
E150FPLSRS
E150FPLSTD
E150FPXSOC
E150FPXSRS
E150FSLSTF
E175FCXSNF
E175FCXSOD
E175FCXSRE
E175FCXSTB
E175FPLSOD
E175FPLSRE
E175FPLSTB
E175FPXSOD
E175FPXSRE
E175FSLSTF
E200FCXSNF
E200FCXSOE
E200FCXSRB
E200FCXSTM
E200FHLSOR
E200FPLSNF
E200FPLSOE
E200FPLSRB
E200FPLSTM
E225FCXSNF
E225FCXSOE
E225FCXSRB
E225FCXSTM
E225FHLSOB
E225FHLSTA
E225FPLSOE
E225FPLSRB
E250FCXSNF
E250FCXSOB
E250FCXSRM
E250FCXSTA
E250FPLSOM
E250FPLSRA
E250FPXSNF
E75FPLSNF
E75FPLSTA
E90FPLSNF
E90FPLSTB
EVINRUDE
BRP EVINRUDE entire parts catalog list:
- DECALS WHITE MODELS » 0215287
E115FPLSNF, E115FPXSNF 2002
E115FPLSOD, E115FSLSOD 2004,2005
E115FPLSRE, E115FSLSRE 2004
E115FPLSTB, E115FPXSTB, E115FSLSTB 2003
E115FPXSOD 2004,2005
E115FPXSRE 2004
E135FCXSNF, E135FPLSNF, E135FPXSNF 2002
E135FCXSOB 2004,2005
E135FCXSTA 2003
E135FPLSOB, E135FSLSOB 2004,2005
E135FPLSRM, E135FSLSRM 2004
E135FPLSTA, E135FPXSTA 2003
E135FPXSOB 2004,2005
E135FPXSRM 2004
E135FSLSTA 2003
E135FSLSTF 2003
E150FCXSNF, E150FPLSNF, E150FPXSNF 2002
E150FCXSOC 2004,2005
E150FCXSRS 2004
E150FCXSTD 2003
E150FHLSOC 2004,2005
E150FHLSRS 2004
E150FPLSOC, E150FSLSOC 2004,2005
E150FPLSRS, E150FSLSRS 2004
E150FPLSTD, E150FPXSTD, E150FSLSTD 2003
E150FPXSOC 2004,2005
E150FPXSRS 2004
E150FSLSTF 2003
E175FCXSNF, E175FPLSNF, E175FPXSNF 2002
E175FCXSOD 2004,2005
E175FCXSRE 2004
E175FCXSTB 2003
E175FPLSOD, E175FSLSOE 2004,2005
E175FPLSRE, E175FSLSRB 2004
E175FPLSTB, E175FPXSTB, E175FSLSTM 2003
E175FPXSOD 2004,2005
E175FPXSRE 2004
E175FSLSTF 2003
E200FCXSNF 2002
E200FCXSOE 2004,2005
E200FCXSRB 2004
E200FCXSTM, E200FHLSTS 2003
E200FHLSOR 2004,2005
E200FPLSNF, E200FPXSNF 2002
E200FPLSOE, E200FPXSOE, E200FSLSOE 2004,2005
E200FPLSRB, E200FPXSRB, E200FSLSRB 2004
E200FPLSTM, E200FPXSTM, E200FSLSTM 2003
E225FCXSNF, E225FCZSNF, E225FHLSNF, E225FPLSNF, E225FPXSNF, E225FPZSNF 2002
E225FCXSOE, E225FCZSOE 2004,2005
E225FCXSRB, E225FCZSRB 2004
E225FCXSTM, E225FCZSTM, E225FPLSTM, E225FPXSTM, E225FPZSTM 2003
E225FHLSOB, E225FHXSOC 2004,2005
E225FHLSTA 2003
E225FPLSOE, E225FPXSOE, E225FPZSOE 2004,2005
E225FPLSRB, E225FPXSRB, E225FPZSRB 2004
E250FCXSNF, E250FCZSNF, E250FPZSNF 2002
E250FCXSOB, E250FCZSOB 2004,2005
E250FCXSRM, E250FCZSRM 2004
E250FCXSTA, E250FCZSTA, E250FPLSTR, E250FPXSTA, E250FPZSTA 2003
E250FPLSOM, E250FPXSOB, E250FPZSOB 2004,2005
E250FPLSRA, E250FPXSRM, E250FPZSRM 2004
E250FPXSNF 2002
E75FPLSNF 2002
E75FPLSTA 2003
E90FPLSNF 2002
E90FPLSTB, E90FSLSTB 2003
Information:
1. Loosen the purge valves and release the air pressure in the air tanks.2. Drain the oil from the oil pan. 3. Remove two short bolts (1) and two longer bolts (3) from manifold (2) and the BrakeSaver housing. Remove manifold (2). Remove the O-ring seals from the manifold. 4. Remove oil temperature sensing unit (4) from the BrakeSaver control valve.5. Disconnect air line (5) and hose assembly (6) from the BrakeSaver control valve. 6. Remove bolt (7) and retainer (8) that hold the oil lines in the BrakeSaver control valve. 7. Disconnect oil lines (9) and (10) from the oil cooler. Remove oil lines (9) and (10) from the BrakeSaver control valve. 8. Remove bolts (12) and BrakeSaver control valve (11) from under the oil pan. The weight is 22 kg (48 lb).9. Remove elbow (13) from the BrakeSaver control valve. Remove the O-ring seals. The following steps are for installation of the BrakeSaver control valve.10. Inspect the O-ring seals for damage, and make replacements if needed. Put clean engine oil on the O-ring seals.11. Install the O-ring seals and elbow (13) on the BrakeSaver control valve.12. Ensure the O-ring seals are in position on the face of the BrakeSaver control valve. Put BrakeSaver control valve (11) in position under the oil pan. Install bolts (12) that hold the BrakeSaver control valve to the oil pan.13. Install oil temperature sensing unit (4) in the BrakeSaver control valve.14. Connect air line (5) and hose assembly (6) to the BrakeSaver control valve.15. Install the O-ring seals on manifold (2). Install manifold (2) in the BrakeSaver control valve. Install the four bolts that hold the manifold to the BrakeSaver housing.16. Ensure the O-ring seals are in place on the oil lines, and install oil lines (9) and (10).17. Install retainer (8) to hold the oil lines in the BrakeSaver control valve. If the bottom plug in the oil pan was removed, put the split (seam) of the gasket for the plug against the oil pan. If either plug on the side of the oil pan was removed, put 9S-3263 Pipe Sealant With Teflon on the threads, and tighten the plug to a torque of 80 11 N m (60 8 lb ft).18. Fill the engine with oil to the correct level. Refer to the Operation and Maintenance Manual, "Refill Capacities" for additional information.Disassemble and Assemble BrakeSaver Control Valve
Start By:a. remove BrakeSaver control valve 1. Remove O-ring seals (1) from the valve body.
Covers (3) and (4) hold a spring under compression. To prevent possible personal injury from flying parts, hold covers (3) and (4) when the bolts are removed.
2. Remove four bolts (2) slowly and evenly from cover (4). Remove the cover.3. Remove cover (3) and the seal from the opposite end of the valve body. 4. Remove spool (8) as an assembly.5. Remove spring (7), stop (10), spring (6) and slug (9).6. Remove the O-ring seals and sleeve (5). 7. Remove bolt (11), plate (13) and diaphragm (12) from the spool. Inspect the pin on the spool, and make a replacement of the pin if there is damage or wear. The following steps are for assembly of the BrakeSaver control valve.
When diaphragm (12) is installed on valve spool (8) ensure that the fabric side is pulled down over the valve spool to make contact with it and the smooth (rubber coated) side is next to the valve body.
8. Put diaphragm (12) in position on valve spool (8).9. Align the hole in plate (13) with the pin in valve spool (8) and install the plate.10. Install bolt (11).11. Install sleeves (5) and the O-ring seals.12. Put spring (7), stop (10), spring (6) and slug (9) in position in valve spool (8).13. Install valve spool (8) into the valve body. As the valve is installed, ensure that the edge at the diaphragm makes contact all the way around with the groove in the valve body. At this time the valve spool end must extend approximately 38.1 mm (1.50 in) from the valve body. Push the valve spool approximately 6.4 mm to 12.7 mm (.25 in. to .50 in) farther into the valve body until a curved depression is caused between the valve spool and valve body. Ensure that there are no wrinkles in the diaphragm.14. Install covers (3) and (4) on the valve body.15. Install three O-ring seals (1).End By:a. install BrakeSaver control valve
Start By:a. remove BrakeSaver control valve 1. Remove O-ring seals (1) from the valve body.
Covers (3) and (4) hold a spring under compression. To prevent possible personal injury from flying parts, hold covers (3) and (4) when the bolts are removed.
2. Remove four bolts (2) slowly and evenly from cover (4). Remove the cover.3. Remove cover (3) and the seal from the opposite end of the valve body. 4. Remove spool (8) as an assembly.5. Remove spring (7), stop (10), spring (6) and slug (9).6. Remove the O-ring seals and sleeve (5). 7. Remove bolt (11), plate (13) and diaphragm (12) from the spool. Inspect the pin on the spool, and make a replacement of the pin if there is damage or wear. The following steps are for assembly of the BrakeSaver control valve.
When diaphragm (12) is installed on valve spool (8) ensure that the fabric side is pulled down over the valve spool to make contact with it and the smooth (rubber coated) side is next to the valve body.
8. Put diaphragm (12) in position on valve spool (8).9. Align the hole in plate (13) with the pin in valve spool (8) and install the plate.10. Install bolt (11).11. Install sleeves (5) and the O-ring seals.12. Put spring (7), stop (10), spring (6) and slug (9) in position in valve spool (8).13. Install valve spool (8) into the valve body. As the valve is installed, ensure that the edge at the diaphragm makes contact all the way around with the groove in the valve body. At this time the valve spool end must extend approximately 38.1 mm (1.50 in) from the valve body. Push the valve spool approximately 6.4 mm to 12.7 mm (.25 in. to .50 in) farther into the valve body until a curved depression is caused between the valve spool and valve body. Ensure that there are no wrinkles in the diaphragm.14. Install covers (3) and (4) on the valve body.15. Install three O-ring seals (1).End By:a. install BrakeSaver control valve
Parts decal EVINRUDE:
0215288
0215288 *DECAL, "EVINRUDE" Port/Stbd
E100FPLSOC, E100FPLSRS, E115FPLSNF, E115FPLSOD, E115FPLSRE, E115FPLSTB, E115FPXSDS, E115FPXSOD, E115FPXSRE, E115FSLSDS, E135FCXSDE, E135FCXSNF, E135FCXSOB, E135FCXSTA, E135FPLSOB, E135FPLSRM, E135FPLSTA, E135FPXSDE, E135FPXSOB, E135FPXSRM, E135FSLSDE
0215270
0215270 *DECAL, "EVINRUDE" Port/Stbd
E100FPLSOC, E100FPLSRS, E115FPLSDS, E115FPLSNF, E115FPLSOD, E115FPLSRE, E115FPLSTB, E115FPXSOD, E115FPXSRE, E135FCXSNF, E135FCXSOB, E135FCXSRM, E135FCXSTA, E135FPLSDE, E135FPLSOB, E135FPLSRM, E135FPLSTA, E135FPLSTF, E135FPXSOB, E135FPXSRM, E135FSLSTA
0215290
0215290 *DECAL, Stripe, Port
E100FPLSOC, E100FPLSRS, E115FPLSNF, E115FPLSOD, E115FPLSRE, E115FPLSTB, E115FPXSDS, E115FPXSOD, E115FPXSRE, E115FSLSDS, E75FPLSNF, E75FPLSTA, E90FPLSNF, E90FPLSTB
0215269
0215269 *DECAL, Stripe, Port
E135FCXSNF, E135FCXSOB, E135FCXSRM, E135FCXSTA, E135FPLSDE, E135FPLSOB, E135FPLSRM, E135FPLSTA, E135FPLSTF, E135FPXSOB, E135FPXSRM, E135FSLSTA, E150FCXSNF, E150FCXSOC, E150FCXSRS, E150FCXSTD, E150FHLSOC, E150FHLSRS, E150FPLSDR, E150FPLSOC, E150FPLSRS
0215292
0215292 *DECAL, Stripe, Port
E135FCXSDE, E135FCXSNF, E135FCXSOB, E135FCXSTA, E135FPLSOB, E135FPLSRM, E135FPLSTA, E135FPXSDE, E135FPXSOB, E135FPXSRM, E135FSLSDE, E135FSLSTA, E135FSLSTF, E150FCXSDR, E150FCXSNF, E150FCXSOC, E150FCXSRS, E150FCXSTD, E150FHLSOC, E150FHLSRS, E150FPLSOC
0215268
0215268 *DECAL, Stripe, Strb
E135FCXSNF, E135FCXSOB, E135FCXSRM, E135FCXSTA, E135FPLSDE, E135FPLSOB, E135FPLSRM, E135FPLSTA, E135FPLSTF, E135FPXSOB, E135FPXSRM, E135FSLSTA, E150FCXSNF, E150FCXSOC, E150FCXSRS, E150FCXSTD, E150FHLSOC, E150FHLSRS, E150FPLSDR, E150FPLSOC, E150FPLSRS
0215233
0215233 DECAL 200 HP Rear
E200FCXSNF, E200FCXSOE, E200FCXSRB, E200FCXSTM, E200FHLSOR, E200FPLSNF, E200FPLSOE, E200FPLSRB, E200FPLSTM, E225FCXSNF, E225FCXSOE, E225FCXSRB, E225FCXSTM, E225FHLSOB, E225FHLSTA, E225FPLSOE, E225FPLSRB, E250FCXSNF, E250FCXSOB, E250FCXSRM, E250FCXSTA
0215230
0215230 DECAL 225 HP Front
E200FCXSNF, E200FCXSOE, E200FCXSRB, E200FCXSTM, E200FHLSOR, E200FPLSNF, E200FPLSOE, E200FPLSRB, E200FPLSTM, E225FCXSNF, E225FCXSOE, E225FCXSRB, E225FCXSTM, E225FHLSOB, E225FHLSTA, E225FPLSOE, E225FPLSRB, E250FCXSNF, E250FCXSOB, E250FCXSRM, E250FCXSTA