0513875 BRACKET, Electrical EVINRUDE
E60ELEIB, E60TTLEIB, E65WMLEIB, E70ELEIE, E70TTLEIE
BRACKET
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$28.57
19-06-2023
0.47[0.21] Pounds
-: -
Sports Parts Inc 05-138-75 Throttle Cable
Made of finest materials including nylon inner lining for smooth operation || Made to OEM specifications || O.E.M. || # 414-935-600
Made of finest materials including nylon inner lining for smooth operation || Made to OEM specifications || O.E.M. || # 414-935-600
$39.06
18-06-2022
-: -
SP1 Replacement Throttle Cable - 05-138-75
Replacement Throttle Cable || 05-138-75 || Sold each
Replacement Throttle Cable || 05-138-75 || Sold each
BRP EVINRUDE entire parts catalog list:
- IGNITION SYSTEM » 0513875
E65WMLEIB 1991
E70ELEIE, E70TLEIE, VE70ELEIE, VE70TLEIE 1991
E70TTLEIE 1991
Information:
Start by:a. Remove rocker arm and shaft assemblies.b. Remove fan drive. When removing cover (1) from the timing gear cover, remove the Allen head screw first. The ten bolts holding the cover will keep pressure on the gasket, which will allow the Allen head screw to be removed more easily. After the allen head screw has been removed, remove the remaining ten bolts from cover (1).1. Remove cover (1) from the timing gear cover. 2. Remove bolts (3) and cover (2) from the flywheel housing.3. Remove plug (4).
For additional information on positioning the crankshaft and camshaft at the compression stroke for No. 1 cylinder (TDC), refer to the Testing & Adjusting Manual.
4. Put the camshaft and crankshaft in the compression stroke position (TDC) for the No. 1 piston as follows: a. Insert the longer bolt (3) [from cover 2] into the hole for plug (4).b. Push bolt (3) against the flywheel. Use a ratchet and tooling (A) to turn the engine and flywheel (in the direction of engine rotation) until bolt (3) seats into the hole in the flywheel.c. Make sure the mark on timing gear (5) and casting rib "X" on timing gear cover (6) are in alignment.
Do not turn the crankshaft or camshaft while camshaft timing gear (5) is removed whenever the rocker shaft assemblies are installed. Damage can be caused to the pistons and valves, or both.
5. Disconnect the wire and remove timing sensor (7).6. Remove one bolt (8) and install a guide bolt (tool B) as shown.7. Remove the remaining six bolts (8). Use tool (C) and a strap to attach a hoist to gear (5). Remove gear (5). 8. Remove the three bolts (9) and thrust plate (10).9. Remove the camshaft and adapter plate (11). 10. Remove adapter plate (11) from camshaft (12).
Care must be taken when removing the camshaft to not damage the highly finished surfaces of both the camshaft and camshaft bearings. Use the following steps and recommended tooling to avoid damage to the engine and components.
11. Use the rocker arm shaft assembly bolts to install tooling (D) into the bolt holes marked "Y" as shown. 12. Install tool (E) onto timing gear cover (6) as shown. Do not tighten the bolts for tooling (E) at this time.
It is necessary to install two pilots (tool F) onto the camshaft. Tool (F) will support the rear of camshaft (12) as the camshaft is moved out of the cylinder head and into tool (E).
13. Move the cam far enough forward to install one tool (F) into the threaded hole in the end diameter of camshaft (12). Again, move the camshaft forward. Install the remaining tool (F) into the back of first tool (F).14. Start camshaft (12) into the bore of tool (E). Snug the bolts holding tool (E) to timing gear cover (6).
When using tool (G) avoid lifting the camshaft. The camshaft should rest on tooling (D). Lifting of the camshaft can cause misalignment as the camshaft is removed, resulting in damage to the camshaft bearings.
15. Remove camshaft (12) as follows:a. Use tool (G) as shown to move camshaft (12) toward the front of the engine. Reposition tool (G) [camshaft lifting hooks] as needed to avoid interference with the cylinder head casting. b. Move camshaft (12) far enough out of the cylinder head to attach a hoist and strap.c. Keep the camshaft level while removing it from the cylinder head. The camshaft weighs 39 kg (85 lb). The following steps are for installing the camshaft.16. Be sure the camshaft and camshaft bearings are thoroughly clean. Put clean engine oil on the lobes and journals of the camshaft. Put a thin coat of clean engine oil on the camshaft bearings.17. Install tool (E) onto the front of timing gear cover (6). Do not tighten the bolts holding tool (E). 18. Install tool (D). 19. Use tool (H) to align tool (E) with the camshaft bearings as shown. Snug the bolts holding tool (E) to the timing gear cover. Remove tool (H). Tool (H) should move freely from the bore of tool (E). Rotating the camshaft in both directions while installing it into the camshaft bearings will help prevent binding.20. Use a hoist to position camshaft (12) into the cylinder head. Move camshaft (12) into the head as far as the strap and hoist will allow.
Tooling (F) must be removed before the camshaft can be completely seated in the cylinder head.
21. Remove the strap and hoist. Rotate the camshaft while moving the camshaft into the bore. Use care not to let the end of the camshaft and tooling (F) drop. Use tool (G) to assist in aligning camshaft (12) with the camshaft bearings if necessary.22. Remove tool (F) and push camshaft (12) the remaining distance into the bore.23. Remove tooling (D) and (E).24. Install adapter plate (11) and thrust plate (10).25. Install tool (B) into the camshaft and adapter plate (11).
Camshaft timing is very important. When installing the camshaft assembly, be sure the timing marks on the camshaft gear and the timing gear cover are aligned when number one cylinder is at top dead center (TDC).
26. Use tool (C) and a strap to position gear (5) onto adapter plate (11). Align the hole in gear (5) with the dowel pin on adapter plate (11). If the timing mark on gear (5) does not align with the casting rib (X) on timing gear cover (6), remove the gear and rotate the camshaft until the gear can be installed with the marks aligned.27. Remove tool (B) and install bolts (8).28. Install timing sensor (7).29. Install cover (1).30. Remove bolt (3) from the flywheel. Install cover (2) and plug (4).End by:a. Install rocker arm and shaft assemblies.b. Install fan drive.
For additional information on positioning the crankshaft and camshaft at the compression stroke for No. 1 cylinder (TDC), refer to the Testing & Adjusting Manual.
4. Put the camshaft and crankshaft in the compression stroke position (TDC) for the No. 1 piston as follows: a. Insert the longer bolt (3) [from cover 2] into the hole for plug (4).b. Push bolt (3) against the flywheel. Use a ratchet and tooling (A) to turn the engine and flywheel (in the direction of engine rotation) until bolt (3) seats into the hole in the flywheel.c. Make sure the mark on timing gear (5) and casting rib "X" on timing gear cover (6) are in alignment.
Do not turn the crankshaft or camshaft while camshaft timing gear (5) is removed whenever the rocker shaft assemblies are installed. Damage can be caused to the pistons and valves, or both.
5. Disconnect the wire and remove timing sensor (7).6. Remove one bolt (8) and install a guide bolt (tool B) as shown.7. Remove the remaining six bolts (8). Use tool (C) and a strap to attach a hoist to gear (5). Remove gear (5). 8. Remove the three bolts (9) and thrust plate (10).9. Remove the camshaft and adapter plate (11). 10. Remove adapter plate (11) from camshaft (12).
Care must be taken when removing the camshaft to not damage the highly finished surfaces of both the camshaft and camshaft bearings. Use the following steps and recommended tooling to avoid damage to the engine and components.
11. Use the rocker arm shaft assembly bolts to install tooling (D) into the bolt holes marked "Y" as shown. 12. Install tool (E) onto timing gear cover (6) as shown. Do not tighten the bolts for tooling (E) at this time.
It is necessary to install two pilots (tool F) onto the camshaft. Tool (F) will support the rear of camshaft (12) as the camshaft is moved out of the cylinder head and into tool (E).
13. Move the cam far enough forward to install one tool (F) into the threaded hole in the end diameter of camshaft (12). Again, move the camshaft forward. Install the remaining tool (F) into the back of first tool (F).14. Start camshaft (12) into the bore of tool (E). Snug the bolts holding tool (E) to timing gear cover (6).
When using tool (G) avoid lifting the camshaft. The camshaft should rest on tooling (D). Lifting of the camshaft can cause misalignment as the camshaft is removed, resulting in damage to the camshaft bearings.
15. Remove camshaft (12) as follows:a. Use tool (G) as shown to move camshaft (12) toward the front of the engine. Reposition tool (G) [camshaft lifting hooks] as needed to avoid interference with the cylinder head casting. b. Move camshaft (12) far enough out of the cylinder head to attach a hoist and strap.c. Keep the camshaft level while removing it from the cylinder head. The camshaft weighs 39 kg (85 lb). The following steps are for installing the camshaft.16. Be sure the camshaft and camshaft bearings are thoroughly clean. Put clean engine oil on the lobes and journals of the camshaft. Put a thin coat of clean engine oil on the camshaft bearings.17. Install tool (E) onto the front of timing gear cover (6). Do not tighten the bolts holding tool (E). 18. Install tool (D). 19. Use tool (H) to align tool (E) with the camshaft bearings as shown. Snug the bolts holding tool (E) to the timing gear cover. Remove tool (H). Tool (H) should move freely from the bore of tool (E). Rotating the camshaft in both directions while installing it into the camshaft bearings will help prevent binding.20. Use a hoist to position camshaft (12) into the cylinder head. Move camshaft (12) into the head as far as the strap and hoist will allow.
Tooling (F) must be removed before the camshaft can be completely seated in the cylinder head.
21. Remove the strap and hoist. Rotate the camshaft while moving the camshaft into the bore. Use care not to let the end of the camshaft and tooling (F) drop. Use tool (G) to assist in aligning camshaft (12) with the camshaft bearings if necessary.22. Remove tool (F) and push camshaft (12) the remaining distance into the bore.23. Remove tooling (D) and (E).24. Install adapter plate (11) and thrust plate (10).25. Install tool (B) into the camshaft and adapter plate (11).
Camshaft timing is very important. When installing the camshaft assembly, be sure the timing marks on the camshaft gear and the timing gear cover are aligned when number one cylinder is at top dead center (TDC).
26. Use tool (C) and a strap to position gear (5) onto adapter plate (11). Align the hole in gear (5) with the dowel pin on adapter plate (11). If the timing mark on gear (5) does not align with the casting rib (X) on timing gear cover (6), remove the gear and rotate the camshaft until the gear can be installed with the marks aligned.27. Remove tool (B) and install bolts (8).28. Install timing sensor (7).29. Install cover (1).30. Remove bolt (3) from the flywheel. Install cover (2) and plug (4).End by:a. Install rocker arm and shaft assemblies.b. Install fan drive.
Parts bracket EVINRUDE:
0313839
0313839 BRACKET, Motor cover, port
55872A, 55972A, 60072B, 60172C, 65272S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, BE50DTLEDC, BE50DTLEUR, BE60ELEDR, BE60ELEUA, BE60TLECM, BE70ELECB, BE70ELEDA, BE70ELEUM, E50DTLECA, E50DTLEOS, E50TTLECA, E50TTLEDC, E50T
0313840
0313840 BRACKET, Motor cover, starboard
55872A, 55972A, 60072B, 60172C, 65272S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, BE50DTLEDC, BE50DTLEUR, BE60ELEDR, BE60ELEUA, BE60TLECM, BE70ELECB, BE70ELEDA, BE70ELEUM, E50DTLECA, E50DTLEOS, E50TTLECA, E50TTLEDC, E50T
0316664
0316664 BRACKET,Idle adjust
60172C, 65272S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, BE50DTLEDC, BE50DTLEUR, BE60ELEDR, BE60ELEUA, BE60TLECM, BE70ELECB, BE70ELEDA, BE70ELEUM, E50DTLECA, E50DTLEOS, E60ELCCR, E60ELCDS, E60ELCEA, E60ELCUC, E60ELEIB,
0329223
0329223 BRACKET, Shift detent
E50TTLECA, E50TTLEDC, E50TTLEOS, E50TTLEUR, E60ELCCR, E60ELCEA, E60ELESM, E60TTLECM, E60TTLEDR, E60TTLEIB, E60TTLENE, E60TTLEOC, E60TTLERS, E60TTLETD, E60TTLEUA, E65RSLC, E65RSLM, E65RSLZ2, E65RWLCDR, E65RWLCOC, E65RWLCRS, E65WRLEEO, E65WRLSIR, E65WR
0331624
0331624 BRACKET, Fuel pump to manifold
BE50DTLEDC, BE50DTLEUR, BE60ELEDR, BE60ELEUA, BE60TLECM, BE70ELECB, BE70ELEDA, BE70ELEUM, E50DTLECA, E50DTLEOS, E50TTLECA, E50TTLEDC, E50TTLEOS, E50TTLEUR, E60ELCCR, E60ELCDS, E60ELCEA, E60ELCUC, E60ELEIB, E60ELENE, E60ELEOC, E60ELERS, E60ELESM, E60E
0125409
0125409 BRACKET
E100STLCCA, E100STLCEM, E100STLEIE, E100STLESB, E100WTLEIB, E100WTLENE, E100WTLERS, E100WTLESM, E100WTLETD, E100WTLZ, E110MLCCA, E110MLCEM, E115JLEIE, E115MLESB, E120TLCEM, E120TLEIE, E120TLESB, E125ESXESS, E140CXCEC, E140CXEIA, E140CXESR, E200CXEIB,
0334191
0334191 BRACKET
BE115ELEDR, BE115ELEUA, BE115GLECM, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, BE250CXECB, BE250CXEDA, BE250CXEUM, BE25ARECA, BE25AREDC, BE25AREUR, B
0336171
0336171 BRACKET, Tilt limit switch
BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, BE50DTLEDC, BE50DTLEUR