5031478 EVINRUDE BRACKET, Fuse case


5031478 BRACKET, Fuse case EVINRUDE E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC BRACKET
5031478 BRACKET, Fuse case EVINRUDE
Rating:
28

Buy BRACKET, Fuse case 5031478 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 42
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E40PL4EES 1999
E40PL4SSC 2000
E50PL4EES 1999
E50PL4EES 1999
E50PL4SSC 2000
E50PL4SSC 2000

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite Nickel Anti-Seize - Note: If reusing the exhaust elbow, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
Illustration 1 g03423737
Remove step (1) and panel (2).
Illustration 2 g02306375
Illustration 3 g03423463
Remove sensor (10 ). Loosen clamp assemblies (3), (5), and (7). Note: Mark the orientation of clamp assembly (5) prior to removal.
Slide elbow (4) into bellows (6) in order to gain clearance. Remove the bellows assembly. Note: Mark the orientation of tube assembly (8) prior to removal.
Loosen clamp assembly (9) and remove tube assembly (8). Installation Procedure
Note: If reusing the exhaust elbow, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
Illustration 4 g02340277
Illustration 5 g02340280
Alignment Wrap (A) is not shown for photographic purposes.
Note: Alignment Wrap (A) will be included with the new bellows assembly. The Tooling will be pre-installed on the bellows. Note: The Alignment Wrap (A) should not be removed until Step 11. Bellows (6) should never be flexed during installation.
Place Mark (B) onto elbow (4). Mark (B) should be a distance of Dimension (X) from the end of elbow (3). Dimension (X) is 40 mm (1.6 inch).
Insert elbow (4) into bellows (6). Elbow (4) should be inserted as far as possible without using force. The action will minimize the overall length of the bellows assembly and will help with installation.
Illustration 6 g02306375
Alignment wrap (A) is not shown for photographic purposes.
Illustration 7 g02340356
The photo is a cutaway view of the ball clamp assembly which is located near the combustion head group.
Illustration 8 g02340357
Cutaway view of the ball clamp assembly.
Position tube assembly (8) and tighten clamp assembly (9).
Prior to installation, position both ball clamp assemblies (3) and (7) onto the bellows assembly.
Position the bellows assembly between the Clean Emissions Module and the turbocharger adapter. Adjust the length of elbow (4) in the slip joint at clamp assembly (5) in order to position the bellows assembly.
Verify that the cup of the Ball Joint (E) does not touch the radius of the Ball (D). Position ball clamp (3) and hand tighten ball clamp (3). Measure Dimension (Y) and Dimension (Z). Dimension (Y) and Dimension (Z) should be equal to each other. Repeat the measurements every 90° around ball clamp (3). If necessary, adjust ball clamp (3).
Repeat Step 6 for ball clamp (7) which is located near the turbocharger.
Verify that Mark (B) is not visible at the slip joint that is positioned near clamp assembly (5). Note: Do not use power tools in order to torque clamp assemblies (3), (5), and (7).
Torque ball clamp (3) to a torque of 35 2 N m (26 1 lb ft).
Torque ball clamp (7) to a torque of 35 2 N m (26 1 lb ft).
Remove alignment wrap (A) from bellows (6).
Torque clamp assembly (5) to a torque of 55 8 N m (41 6 lb ft).
Apply Tooling (A) to the threads of sensor (10). Tighten sensor (10) to a torque of 50 10 N m (37 7 lb ft).
Illustration 9 g03423737
Install step (1) and panel (2).


Parts bracket EVINRUDE:

5031480
 
5031480 BRACKET, Neutral switch
E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC
5031401
 
5031401 BRACKET, Fuel filter
E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC
5031404
 
5031404 BRACKET, Fuel injector
E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC
5031592
 
5031592 BRACKET CONTROL CABLES
E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC
5031593
 
5031593 BRACKET CONTROL CABLES
E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC
5031532
 
5031532 BRACKET, Lower mount
E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC
5031475
 
5031475 BRACKET
E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC
5031496
 
5031496 BRACKET, Swivel
E40PL4EES, E50PL4EES, E50PL4EES
Back to top