5031506 EVINRUDE BUSHING, Tilt cylinder, upper


5031506 BUSHING, Tilt cylinder, upper EVINRUDE E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC BUSHING
5031506 BUSHING, Tilt cylinder, upper EVINRUDE
Rating:
83

Buy BUSHING, Tilt cylinder, upper 5031506 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$41.29
 

13-10-2020
4.40924524[1.80] Pounds
-: -
Connected Essentials 5031506 Tailored Heavy Duty Custom Fit Car Mats, for 93 Convertible (1998-2002), Black with Red Trim, Premium
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Saab 93 Convertible (1998-2002) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Number on catalog scheme: 23
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 241-0124 Valve Spring Compressor 1
B 441-0714 Tool As 1 Start By:
Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01134319
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Use Tooling (A) to compress inner valve spring (3) and outer valve spring (4). Remove valve spring keepers (1).
Carefully remove Tooling (A).
Remove valve rotator (2), inner valve spring (3), and outer valve spring (4).
Remove washer (5) from the exhaust valve guide.
Remove inlet valve (6) and exhaust valve (7) from the valve guides.Note: If the exhaust valves or the inlet valves will be reused, put identification marks on the exhaust valves and the inlet valves for installation purposes.
Illustration 2 g01133465
Use Tooling (B) to check the valve springs (spring force). Refer to Specifications, "Cylinder Head Valves" for additional information on the valve springs.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 241-0124 Valve Spring Compressor 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01134256
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Apply clean engine oil to the stem of exhaust valves (7). Install the exhaust valve into exhaust valve guide (10).
Install washer (5), inner valve spring (3), and outer valve spring (4) on exhaust valve guide (10).
Position valve rotator (2) on the stem of the exhaust valve.
Use Tooling (A) to compress inner valve spring (3) and outer valve spring (4). Install valve spring keepers (1) on the exhaust valve.
The valve spring keepers can be thrown from the valve when the valve spring compressor is released. Ensure that the valve spring keepers are properly installed on the valve stem. To help prevent personal injury, keep away from the front of the valve spring keepers and valve springs during the installation of the valves.
Carefully remove Tooling (A). Strike the top of the valves with a soft faced hammer to ensure that valve spring keepers (1) are properly installed on the valve stems.
Apply clean engine oil to the stem of inlet valves (6). Install the inlet valve into inlet valve guide.Note: Ensure that valve stem seal (8) is installed on inlet valve guide (9).
Install inner valve spring (3) and outer valve spring (4) on inlet valve guide (9).
Position valve rotator (2) on the stem of the inlet valve.
Use Tooling (A) to compress inner valve spring (3) and outer valve spring (4). Install valve spring keepers (1) on the inlet valve.
The valve spring keepers can be thrown from the valve when the valve spring compressor is released. Ensure that the valve spring keepers are properly installed on the valve stem. To help prevent personal injury, keep away from the front of the valve spring keepers and valve springs during the installation of the valves.
Carefully remove Tooling (A). Strike the top of the valves with a soft faced hammer to ensure that valve spring keepers (1) are properly installed on the valve stems.End By:
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".


Parts bushing EVINRUDE:

5030852
BUSHING, Steering arm
5030852 BUSHING, Steering arm
E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5031543
 
5031543 BUSHING, Driveshaft
E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC
5031691
 
5031691 BUSHING, Propeller
E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC
5031271
 
5031271 BUSHING
E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC
5031497
BUSHING, Tilt tube
5031497 BUSHING, Tilt tube
E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC
5031491
 
5031491 BUSHING, Tilt lock lever
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC
Back to top