5032064 BUSHING, Steering arm EVINRUDE
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4SIR, E50PL4SIR, E50PL4SIR
BUSHING

Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$41.62
03-08-2020
4.40924524[1.80] Pounds
-: -
Connected Essentials 5032064 Grey with Blue Trim Tailored Heavy Duty Custom Fit Car Mats Kia Ceed (2007-2012)
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Kia Ceed (2007-2012) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Kia Ceed (2007-2012) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
BRP EVINRUDE entire parts catalog list:
- STERN & SWIVEL BRACKET » 5032064
E30EL4SIC, E30PL4SIC, E30R4SIC, E30RL4SIC, E30TE4SIC, E30TEL4SIC 2001
E30EL4SSS, E30PL4SSS, E30R4SSS, E30RL4SSS, E30TE4SSS, E30TEL4SSS 2000
E40PL4SIR 2001
E50PL4SIR 2001
E50PL4SIR 2001
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 177-7861 Hose As 1
6V-4143 Couplers 2
8T-0860 Pressure Gauge (0 to 40,000-kPa (0 to 5,800-psi)) 1 Note: Permit only one operator on the machine. Keep all other personnel away from the machine or in the operator's sight.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Move the machine to a hard, level surface.
Place the transmission direction and speed control in the NEUTRAL position and in any speed position. Engage the steering and transmission lock lever on STIC steering machines.
Engage the parking brake. Place wheel blocks in front of the wheels and behind the wheels.
When the work tool is raised for testing or for adjusting, make sure that the work tool is supported correctly. Also, make sure that the bucket and/or attachment is fully in the DUMP position. The lift circuit has high oil pressure when the lift arms raise the front of the machine.Note: Do not stop the machine with the front of the machine off the ground unless this is required for a test. Lower the machine to the ground and stop the engine.
If the machine is equipped with the ride control system, with the engine speed above 1500 rpm, press and hold the ride control switch to the SERVICE position. Move the joystick control lever to the FLOAT position. This will relieve all of the hydraulic pressure in the ride control accumulator.
Decrease the engine speed to low idle.
Stop the engine.
Install the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Move the key start switch to the ON position.
Move the joystick control lever through the full range of travel. This will relieve any pressure that may be present in the implement hydraulic system.
Move the steering control several times in both directions to release the pressure in the steering system.
Depress the brake pedal at least 80 times to release any pressure in the braking system.
Depress the breaker relief valve on the hydraulic tank to release the pressure in the hydraulic tank.
Illustration 1 g00975402
(1) Pressure tap (for the rod end of the tilt cylinder) (2) Pressure tap (for the head end of the tilt cylinder)
Connect Tooling (A) to pressure tap (1). If there is any pressure on the gauge, move the joystick control lever to all positions until all the pressure is removed from the system.
Connect Tooling (A) to pressure tap (2). If there is any pressure on the gauge, move the joystick control lever to all positions until all the pressure is removed from the system.
The pressure in the hydraulic system has now been released. The lines, fittings and components can be removed.
Remove the test equipment.
Parts bushing EVINRUDE:
5032111
5031894
5032075
5032075 BUSHING, Tilt rod, upper
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4SIR, E50PL4SIR, E50PL4SIR
5032312
5032334
5032138
5031577
5032058
5032058 BUSHING, Tilt tube
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4SIR, E50PL4SIR, E50PL4SIR