0320492 EVINRUDE CAM FOLLOWER


0320492 CAM FOLLOWER EVINRUDE 10524C, 10624G, 10724A, 10824M, 15504C, 15604A CAM
0320492 CAM FOLLOWER EVINRUDE
Rating:
38

Buy CAM FOLLOWER 0320492 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 32
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

10524C, 10525C, 10554C, 10555C 1975
10624G, 10624H, 10624R, 10625G, 10625H, 10625R, 10654G, 10654H, 10654R, 10655G, 10655H, 10655R 1976
10724A, 10725A, 10754A, 10755A, 15704M, 15705M, 15754M 1977
10824M, 10825M, 10835M, 10854M, 10855M, 15804B, 15805B, 15854B, 15855B 1978
15504C, 15505C, 15554C, 15555C 1975
15604A, 15604R, 15605A, 15605R, 15654A, 15654R, 15655A, 15655R 1976

Information:


Illustration 1 g00876271
Installed crankshaft timing pin
Put the No. 1 piston at the Top Center Position on the compression stroke. Refer to Testing and Adjusting, "Finding the Top Center Position for the No. 1 Piston". Install the crankshaft timing pin.
Illustration 2 g00876210
Right side view (1) Plug for the right camshaft timing hole (2) Right camshaft timing pin in the storage position
Illustration 3 g00876449
Left side view (3) Plug for the left camshaft timing hole (4) Left camshaft timing pin in the storage position
Remove plugs (1) and (3) from the camshaft timing holes on both sides of the engine. Remove timing bolts (2) and (4) from the storage positions.
Illustration 4 g00876290
Camshaft timing hole
Install camshaft timing pins (2) and (4) through the holes for plugs (1) and (3) into the camshaft timing holes.For correct timing, both of the camshaft timing pins must fit into the holes in the camshafts when the crankshaft is pinned.If the crankshaft and both camshafts are pinned, the camshafts are correctly timed.If the crankshaft is pinned and either camshaft cannot be pinned, the camshaft position must be adjusted. Proceed to "Camshaft Timing Adjustment".Camshaft Timing Adjustment
Note: Before any timing adjustments are made, the timing must be checked. Checking the timing will determine if an adjustment is required. Refer to "Camshaft Timing Check".Note: If both camshafts must be adjusted, perform this procedure for one camshaft and then perform this procedure for the other camshaft.
Illustration 5 g00876423
Right side view (1) Plug for the right camshaft timing hole (2) Right camshaft timing pin in the storage position (3) Crankshaft's timing pin in the storage location
Illustration 6 g00877656
Right side view behind the barring device (4) Cover for the crankshaft's timing window
Illustration 7 g00876682
Left side view (5) Plug for the left camshaft timing hole (6) Left camshaft timing pin in the storage position
Illustration 8 g00876271
Installation of the crankshaft timing pin
Verify the following conditions:
Plugs (1) and (5) are removed from the engine.
Camshaft timing pins (2) and (6) are removed from the engine.
Cover (4) for the crankshaft's timing window is removed.
Crankshaft timing pin (3) is installed in the timing window through the guide sleeve into the crankshaft timing pin bracket.
The No. 1 piston is at the Top Center Position on the compression stroke. Refer to Testing and Adjusting, "Finding the Top Center Position for the No. 1 Piston".
If the camshaft is rotated with the timing pin installed, the timing pin will break. This can result in further damage. Make sure to remove the timing pin before the camshaft is rotated.
If the crankshaft is rotated when the timing pin is installed, the timing pin will break. This can result in further damage. Make sure to remove the timing pin before the crankshaft is rotated.
Remove crankshaft timing pin (f3). Operate the prelube pump and turn the crankshaft in the opposite direction of normal rotation for approximately 20 degrees.
Illustration 9 g00876290
Camshaft timing hole
Operate the prelube pump and slowly turn the crankshaft in the direction of normal rotation while both of the camshafts are observed through the ports for plugs (1) and (5). When the first camshaft timing hole is aligned through the port, stop the crankshaft. Install camshaft timing pin (2) or (6) through port (1) or (5) and into the camshaft.


Parts cam EVINRUDE:

0320434
CAM, Throttle control
0320434 CAM, Throttle control
10424G, 10524C, 10624G
0318929
 
0318929 CAM, Magneto
10424G, 10524C, 10624G, 15404G, 15504C, 15604A
0320486
 
0320486 CAM FOLLOWER,Starter interlock
10524C, 10624G, 10724A, 10824M, 15504C, 15604A
0320819
CAM,Throttle control
0320819 CAM,Throttle control
10624G, 10724A, 10824M, 15504C, 15604A
Back to top