0312714 EVINRUDE CAP,Thermostat housing


0312714 CAP,Thermostat housing EVINRUDE 5802B, 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6704M, 6802A, 6804B, 6902M, 6904E CAP
0312714 CAP,Thermostat housing EVINRUDE
Rating:
53

Buy CAP,Thermostat housing 0312714 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

BRP EVINRUDE entire parts catalog list:

5802B, 5802E, 5802M, 5803B, 5803E, 5803M 1968
6002B, 6003B 1970
6102E, 6102G, 6103E, 6103G 1971
6202D, 6203D 1972
6302S, 6303S 1973
6402C, 6403C 1974
6504R, 6505R 1975
6604A, 6605A 1976
6704M, 6705M 1977
6802A, 6802C, 6802R, 6803A, 6803C, 6803R 1968
6804B, 6805B 1978
6902M, 6903M 1969
6904E, 6905E 1979

Information:

START BY:a. remove water pump (industrial or marine engines) 1. Remove O-ring seal (1) from adapter (2).2. Remove adapter (2) with a screwdriver. Remove the seal from the edge of adapter (2).3. Remove bolt (3) and the washer. 4. Remove impeller (4) from the water pump housing with tooling (A). 5. Remove seal assembly (5). Remove ring and seal (6). 6. Remove the bolt and washer that hold gear (7) on the water pump shaft.7. Remove gear (7) with tooling (B).8. Remove the bolts and retainer (9).9. Remove O-ring seal (8). 10. Remove shaft (10) and the bearings as a unit.11. Remove bearing (11), spacer (12) and bearing (13) from shaft (10).12. Remove the lip-type seal from the gear side of the water pump. Remove the ring and seal from the impeller side of the water pump.Assemble Water Pump (Industrial And Marine Engines)
1. Use steel wool to remove deposits or corrosion from the pump shaft. Some corrosion and/or deposits on the pump shaft, where the carbon seal assembly and ceramic ring meet, is normal and does not require replacement of the shaft. Replace the shaft only if pitting, corrosion or scoring can provide a path for coolant to leak between the seal and the pump shaft.
Do not use any sandpaper that will leave visible scratches on the pump shaft.
2. A polished area on the water pump shaft indicates a carbon seal assembly has been spinning on the shaft. Before installing a new seal assembly, use a fine grit sandpaper to clean the polished area.3. Use 6V1541 Quick Cure Primer to clean the water pump shaft and the ceramic ring seal counterbore in the pump housing. 4. Install seal (1) as shown with tool (A). Lubricate the lip of seal (1) with clean engine oil or glycerine. 5. Install bearing (4), spacer (3) and bearing (5) on shaft (2). 6. Install shaft (2) into the pump housing.7. Install retainer (7) and O-ring seal (8) on the pump housing.8. Install gear (6) and the washer and bolt that fasten gear (6) to shaft (2). Tighten the bolt to a torque of 205 25 N m (150 18 lb.ft.).
The carbon seal assembly must rotate with the water pump shaft. Do not use any lubricant, except clean water or coolant, that will reduce the friction between the seal and the shaft.
9. Immerse the carbon seal assembly in clean water or coolant. Avoid contaminating the seal "faces" with any grease or oil. Also, avoid stretching the rubber of the seal during installation. Stretching the seal will reduce the service life of the seal.10. Use tooling (B) and hand pressure to install rubber seal (9) and ceramic ring (10) as a unit into the pump housing bore. Make sure the identification marks (holes or groove) on the ceramic ring face are installed toward the inside of rubber seal (9).11. Remove the spring from seal assembly (11). Use tool (B) and hand pressure to install seal assembly (11). Push the seal assembly on the shaft until the carbon ring on the seal assembly makes light contact with the smooth face of ceramic ring (10). 12. Install spring (12) on the seal assembly and impeller (13) on the shaft. Install the bolt and washer that fastens impeller (13) to the shaft. Tighten the bolt to a torque of 39 3 N m (29 2 lb.ft.). 13. Install seals (14) on adapter (15). Lubricate the seals with clean engine oil or glycerine.14. Install adapter (15) into the pump housing. Make sure the notch in the adapter is in alignment with dowel (16).END BY:a. install water pump (industrial or marine engine)


Parts cap EVINRUDE:

0312629
CAP, Filter
0312629 CAP, Filter
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, 18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25902B, 3802A, 4006E, 4106D, 4206S, 4306C, 4406R, 4506A, 4606M, 4706B, 480
0203830
 
0203830 CAP,Propeller shaft
3802A, 4006E, 4106D, 4206S, 4306C, 4902B, 5802B
Back to top