0393172 EVINRUDE CARB ASSY.,Lower, 90


0393172 CARB ASSY.,Lower, 90 EVINRUDE E115MLCTE, E140MLCTE, E90MLCTE CARB
0393172 CARB ASSY.,Lower, 90 EVINRUDE
Rating:
103

Buy CARB ASSY.,Lower, 90 0393172 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$182.45
 

12-09-2017

K&M Ma: K&M Manufacturin
K&M 039-3172 JD 8000-8020 Series Monitor Bracket
Includes removable 6" x 9" tray that mounts at various locations along the bracket to keep your cell phone and tools right where you want them||Well-suited for use with multiple monitors||Allows for the use of normal bolts to mount monitors or optional RAM type mount (RAM 2.43" x 1.31" diamond base with 1" ball)||Attaches quickly and easily
Number on catalog scheme: 39317
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E115MLCTE, E115TLCTE, E115TXCTE 1983
E140MLCTE, E140TRLCTE, E140TRXCTE 1983
E90MLCTE, E90TLCTE, E90TXCTE 1983

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0074 Slide Hammer Puller 1
8B-7557 Adapter 1
B 1P-0520 Driver Group 1
C 138-7575 Link Bracket 2 Start By:
Remove the engine oil filter housing. Refer to Disassembly and Assembly, "Engine Oil Filter Housing - Remove".
Remove the crankshaft front seal and the wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Front Seal and Wear Sleeve - Remove".
Remove accessory drive (front). Refer to Disassembly and Assembly, "Accessory Drive (Front) - Remove".
Remove the engine oil and water pump drive. Refer to Disassembly and Assembly, "Engine Oil and Water Pump Drive - Remove".
Remove the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01255428
Remove the clips from front drive housing (3).
Attach Tooling (C) and a suitable lifting device to mounting bracket (1). The weight of mounting bracket (1) is approximately 70 kg (154 lb).
Remove bolts (2) and mounting bracket (1).
Illustration 2 g01255435
Remove elbow (5) and tube (4).
Remove cover (6) and the O-ring seal from front drive housing (3).
Remove the bolts from the end of shaft (8). Use Tooling (A) to remove shaft (8) and idler gear (7) from both sides of the engine.
Use Tooling (B) and a suitable press to remove the bearing from idler gear (7).
Illustration 3 g01255488
Remove washers (10) from front drive housing (3).
Attach Tooling (C) and a suitable lifting device to front drive housing (3). The weight of front drive housing (3) is approximately 200 kg (450 lb).
Remove the bolts that hold the engine oil pan to front drive housing (3). Remove bolts (9), front drive housing (3), and the front drive housing gasket. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 1P-0520 Driver Group 1
C 138-7575 Link Bracket 2
D - Guide Bolt
5/8 - 11 NC by 8 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 4 g01255488
Install the front drive housing gasket on the cylinder block. Install Tooling (D) in the cylinder block.
Attach Tooling (C) and a suitable lifting device to front drive housing (3). The weight of front drive housing (3) is approximately 200 kg (450 lb). Position front drive housing (3) on Tooling (D).
Install bolts (9) in front drive housing (3) and tighten the bolts evenly. Cut the excess front drive housing gasket at the face of the cylinder block. Apply sealant to the cut corners of the gasket.
Inspect the condition of the gasket on the engine oil pan. Replace the gasket, if necessary. Install the bolts that attach the engine oil pan to front drive housing (3).
Install washers (10) in front drive housing (3).
Illustration 5 g01255435
Use Tooling (B) to install the bearing in idler gear (7). The bearing must have a diameter of 105.97 0.01 mm (4.172 0.001 inch) after installation.
Place clean engine oil on the O-ring seal of shaft (8). Install idler gear (7) and shaft (8) on both sides of the engine.
Place clean engine oil on the O-ring seal and install cover (6) on front drive housing (3).
Lubricate the O-ring seals on tube (4) with glycerin. Install tube (4) and elbow (5).
Illustration 6 g01255428
Attach Tooling (C) and a suitable lifting device to mounting bracket (1). The weight of mounting bracket (1) is approximately 70 kg


Parts carb EVINRUDE:

0392596
 
0392596 CARB ASSY., Upper, 90
E115MLCNB, E115MLCTE, E140MLCNB, E140MLCTE, E90MLCNB, E90MLCTE
0392597
 
0392597 CARB ASSY., Lower, 90
E115MLCNB, E115MLCTE, E140MLCNB, E140MLCTE, E90MLCNB, E90MLCTE
0392600
 
0392600 CARB ASSY., Upper, 115
E115MLCNB, E115MLCTE, E140MLCNB, E140MLCTE, E90MLCNB, E90MLCTE
0392601
 
0392601 CARB ASSY., Lower, 115
E115MLCNB, E115MLCTE, E140MLCNB, E140MLCTE, E90MLCNB, E90MLCTE
0393171
CARB ASSY.,Upper, 90
0393171 CARB ASSY.,Upper, 90
E115MLCTE, E140MLCTE, E90MLCTE
0393173
CARB ASSY.,Upper,115
0393173 CARB ASSY.,Upper,115
E115MLCTE, E140MLCTE, E90MLCTE
0393174
 
0393174 CARB ASSY.,Lower,115
E115MLCTE, E140MLCTE, E90MLCTE
0393175
CARB ASSY.,Upper,140
0393175 CARB ASSY.,Upper,140
E115MLCTE, E140MLCTE, E90MLCTE
Back to top