0398407 EVINRUDE CARB. ASSY.


0398407 CARB. ASSY. EVINRUDE E275CLCUR, E300CLCUR CARB
0398407 CARB. ASSY. EVINRUDE
Rating:
43

Buy CARB. ASSY. 0398407 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
 
$69.05
 

13-09-2017

K&M Ma: K&M Manufacturin
K&M 039-8407 Vinyl KM 112 Backrest Cushion, Black Vinyl
Durable Black Vinyl covering||Foam cushion to ensure operator comfort||Strong wear resistance
Number on catalog scheme: 39840
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E275CLCUR, E275CXCUR, E275PLCUR, E275PXCUR 1987
E300CLCUR, E300CXCUR, E300PLCUR, E300PXCUR 1987

Information:


Illustration 1 g06318889
Table 1
Troubleshooting Test Steps Values Results
1. Check the Coolant Level
Allow the engine to cool prior to removal of the cooling system pressure cap.
A. Remove electrical power from the Electronic Control Module (ECM).
B. Check the coolant level. Refer to the Operation and Maintenance Manual for the proper procedure to check the coolant level.
Coolant Level
Result: The coolant is at the proper level.
Proceed to Test Step 2.
Result: The coolant level is low.
Repair: Add coolant according to the procedure in the Operation and Maintenance Manual.
There may be a leak in the cooling system. Identify the source of the coolant leak. Repair the leak. Refer to Systems Operation/Testing and Adjusting, "Cooling System" for additional information.
2. Verify that the "Coolant Level Sensor" Parameter is Programmed Correctly
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Use Cat ET to verify that the "Coolant Level Sensor" parameter is programmed to "Installed".
C. Remove electrical power from the ECM.
Parameter Programmed
Result: The "Coolant Level Sensor" parameter is programmed correctly.
Proceed to Test Step 3.
Result: The "Coolant Level Sensor" parameter is not programmed correctly.
Repair: Program the "Coolant Level Sensor" parameter to "Installed".
If the problem is not resolved, proceed to Test Step 3.
3. Check the Supply Voltage at the Sensor Connector
A. Disconnect the coolant level sensor at the sensor connector.
B. Restore electrical power to the ECM.
C. Measure the voltage between the following wiring harness connector terminals for the coolant level sensor:
A (sensor supply) and B (sensor return)
D. Remove electrical power from the ECM.
5.0 0.5 VDC
Result: The voltage measurement is 5.0 0.5 VDC.
The supply voltage is reaching the sensor. Proceed to Test Step 4.
Result: The voltage measurement is not 5.0 0.5 VDC.
Repair: The sensor supply voltage is not reaching the sensor. There is a problem in the circuit for the sensor supply. Repair the wiring harness between the sensor and the ECM.
If the problem is not resolved, proceed to Test Step 4.
4. Short the Signal Wire to Ground and Monitor the Status for "Coolant Level"
A. Fabricate a jumper wire that is long enough to create a short circuit between two terminals at the coolant level sensor harness connector. Crimp connector pins to each end of the jumper wire.
B. Install the jumper wire between terminals B (sensor return) and C (sensor signal) on the harness side of the connector for the coolant level sensor.
C. Connect Cat ET.
D. Use Cat ET to monitor the following parameter:
- "Coolant Level"
E. Remove the jumper wire. Connect the harness connector for the coolant level sensor.
5 VDC
Result: The status changes from "LOW" to "OK" when the jumper wire is installed. The ECM and the wiring harness to the coolant level sensor are OK.
Repair: Replace the coolant level sensor.
Verify that the repair eliminated the problem.
Result: The status does not change from "LOW" to "OK" when the jumper wire is installed.
Repair: The problem is between the ECM and the sensor connector. Repair the wiring harness.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts carb EVINRUDE:

0398557
CARB. REPAIR KIT
0398557 CARB. REPAIR KIT
E120TLCCA, E120TLCEM, E120TLCUR, E120TLESB, E125ESXESS, E125ESXW, E140CXCCS, E140CXCEC, E140CXESR, E140TLCUA, E185ESXESS, E185ESXW, E200CXCCR, E200CXCEA, E200CXESM, E200STLCUA, E225CLCUB, E225CXCCE, E225CXCED, E225CXESS, E250CXEIE, E275CLCUR, E275CXC
0431938
 
0431938 CARB. BODY ASSY.
E275CLCUR, E300CLCUR
0398069
 
0398069 CARB. BODY ASSY.
E275CLCUR, E300CLCUR
0398408
 
0398408 CARB. ASSY.
E275CLCUR, E300CLCUR
Back to top