0436935 EVINRUDE CARB. ASSY., Stbd., 175GL, SL


0436935 CARB. ASSY., Stbd., 175GL, SL EVINRUDE BE150ELEDB, BE175EXEDB, E150ELEOM, E150ELERA, E175EXARC, E175EXEOM CARB
0436935 CARB. ASSY., Stbd., 175GL, SL EVINRUDE
Rating:
103

Buy CARB. ASSY., Stbd., 175GL, SL 0436935 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 43693
 

BRP EVINRUDE entire parts catalog list:

BE150ELEDB, BE150EXEDB, BE150GLEDB, BE150NXEDB, E150ELEDB, E150EXEDB, E150GLEDB, E150JLEDB, E150NXEDB, E150SLEDB, L150GLEDC 1996
BE175EXEDB, BE175GLEDB, BE175NXEDB, E175EXEDB, E175GLEDB, E175NXEDB, E175SLEDB 1996
E150ELEOM, E150EXEOM, E150GLEOM, E150JLEOM, E150NXEOM, E150SLEOM, L150GLEOS, VE150HLEOS 1995
E150ELERA, E150ELERV, E150EXARC, E150EXARV, E150EXERA, E150EXERV, E150GLERA, E150GLERV, E150JLERA, E150JLERV, E150NXARC, E150NXARV, E150NXERA, E150NXERV 1994
E175EXARC, E175EXARV, E175EXERA, E175EXERV, E175GLERA, E175NXARC, E175NXARV, E175NXERA, E175NXERV, E175SLERA 1994
E175EXEOM, E175GLEOM, E175NXEOM, E175SLEOM 1995

Information:

1. Check each bearing cap (1) for its location on the engine. Each cap has an arrow which is toward the front of the block and a number which gives the location of that cap. Keep each bearing with the correct cap.2. Remove bearing caps No. 2 through No. 6. Remove thrust plates from No. 4 upper bearing.3. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft as shown. Remove No. 1 and No. 7 main bearing caps. Remove the crankshaft. Weight of the crankshaft is 181 kg (400 lb).
Be careful not to damage the crankshaft journals when the crankshaft is removed.
4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface a distance of 6.4 0.5 mm (.25 .02 in).2. Install dowel (2) until it is extended from the surface a distance of 4.1 0.5 mm (.16 .02 in). 3. Heat crankshaft gear (3) to a maximum temperature of 232°C (450°F). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2).4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft. 5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block.
Use care to prevent damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
For more detail about installation of main bearings, see Remove And Install Crankshaft Main Bearings.6. Check the bearing clearances with Plastigage.7. Put clean engine oil on the bolts for caps No. 1 and No. 7. Install No. 1 and No. 7 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block. 8. Install thrust plates (5) for the No. 4 upper main bearing. Install the thrust plates with the side that has identification "BLOCK SIDE" toward the cylinder block.9. Put clean oil on the bolts for caps No. 2 through No. 6. Install caps No. 2 through No. 6 with the bolts finger tight. Make sure the arrows are toward the front of the block.
Do not use an impact wrench to tighten the bolts the additional 120°.
10. Tighten the cap bolts as follows:a. Tighten the bolts on the tab end of the caps first to a torque of 260 14 N m (190 10 lb ft).b. Tighten the bolts on the other end of the caps to a torque of 260 14 N m (190 10 lb ft).c. Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120° more. Tighten the bolts on the tab end of the cap 120° more. 11. Check the end play of the crankshaft with tool (A). Make sure the dial indicator is against a machined surface. End play with new thrust plates must be 0.15 to 0.51 mm (.006 to .020 in). The maximum end play with used thrust plates is 0.89 mm (.035 in).End By:a. install pistonsb. install flywheel housingc. install timing gear coverd. install oil pump


Parts carb EVINRUDE:

0435082
 
0435082 CARB. BODY AY., 150 XP, GT, 175
E150ELEIS, E150ELENC, E150ELERA, E150ELETG, E175EXARC, E175EXATG, E175EXEIS, E175EXENC
0434639
 
0434639 CARB. ASSY., Port, 150 XP, GT
E150ELEIS, E150ELENC, E150ELERA, E150ELETG, E175EXARC, E175EXATG, E175EXEIS, E175EXENC
0435295
 
0435295 CARB, ASSY., Stbd., 175
E150ELENC, E150ELERA, E150ELETG, E175EXARC, E175EXATG, E175EXENC
0435296
 
0435296 CARB, ASSY., Port, 175
E150ELENC, E150ELERA, E150ELETG, E175EXARC, E175EXATG, E175EXENC
0435528
 
0435528 CARB ASSY., Stbd. 150
E150ELENC, E150ELERA, E150ELETG, E150WTLETG, E175EXARC, E175EXATG, E175EXENC
0436016
 
0436016 CARB. ASSY., Stbd., 150JL
E150ELERA, E175EXARC
0436017
 
0436017 CARB. ASSY., Port, 150JL
E150ELERA, E175EXARC
0436830
Back to top