0390990 EVINRUDE CARBURETOR REPAIR KIT


0390990 CARBURETOR REPAIR KIT EVINRUDE E4BRCICI, E4RDHCDE, E5RCIC, E5RCSS, E5RHCNR, E8RCIC, E8RCNR, E8RCSS CARBURETOR
0390990 CARBURETOR REPAIR KIT EVINRUDE
Rating:
58

Buy CARBURETOR REPAIR KIT 0390990 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 42
 

BRP EVINRUDE entire parts catalog list:

E4BRCICI, E4BRLCIC 1981
E4RDHCDE 1986
E5RCIC, E5RHCIC, E5RHLCIC, E5RLCIC 1981
E5RCSS, E5RHCSS, E5RHLCSS, E5RLCSS 1980
E5RHCNR, E5RHLCNR 1982
E8RCIC, E8RLCIC 1981
E8RCNR, E8RLCNR, E8SRLCNR 1982
E8RCSS, E8RLCSS 1980

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 360-8376 Capping Kit 1 Start By:
Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove" for the correct procedure.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Note: Plug or cap all open ports with new plugs or new caps.
Illustration 1 g06384237
Disconnect the Original Equipment Manufacturers (OEM) harness assembly from harness assembly (1).
Remove nut (3) and washer (2) from harness assembly (1).
Position harness assembly (1) away from bracket (5).
Remove bolts (4) and bracket (5) from bracket (6).
Illustration 2 g06142945
Illustration 3 g06384220
Illustration 4 g06324253
Thoroughly clean fuel manifold (9) and the area around the fuel manifold.
Disconnect wiring harness (8) from Exhaust Gas Recirculation (EGR) valve assembly (7)
Disconnect wiring harness (10) from fuel pressure sensor (9).
Remove banjo bolt (11) and sealing washers (13) (not shown) from banjo connection (12). Use Tooling (A) to plug fuel pressure relief valve (14) and cap the banjo connection.
Remove bolts (16) from fuel manifold (15). Remove the fuel manifold from the cylinder head.
If necessary, remove relief valve (14) from fuel manifold (15). Refer to Disassembly and Assembly, Relief Valve (Fuel) - Remove and Install for the correct procedure.Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that all ports on the fuel manifold are capped. Ensure that the fuel manifold is externally clean and free from damage.Note: Do not install a fuel manifold that has not been plugged. All plugs and caps must be left in place until the fuel injection lines are about to be installed.
Illustration 5 g06324253
If necessary, install relief valve (14) to fuel manifold (15). Refer to Disassembly and Assembly, Relief Valve (Fuel) - Remove and Install for the correct procedure.
Position fuel manifold (15) onto the cylinder head. Loosely install bolts (16) to the fuel manifold.
Install new fuel injection lines finger tight. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install" for the correct installation procedure.Note: Do not torque the nuts for the fuel injection lines at this stage of the assembly procedure.
Tighten bolts (16) to a torque of 22 N m (195 lb in).
Tighten the nuts for the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install" for the correct procedure.
Remove the plug from relief valve (14) and cap from banjo connection (12).
Install a new sealing washers (13) (not shown) onto banjo bolt (11). Position banjo connection (12) onto relief valve (14). Install the banjo bolt and the remaining new sealing washer. Tighten the banjo bolt to a torque of 15 N m (133 lb in). Ensure that the fuel line is not strained as the banjo bolt is tightened.
Illustration 6 g06384220
Illustration 7 g06142945


Parts carburetor EVINRUDE:

0391937
CARBURETOR REPAIR KIT
0391937 CARBURETOR REPAIR KIT
E4BRHCNR, E4BRHCOB, E4BRHCRM, E4BRHCTA, E4RDHCDE, E4WCNR, E5RCIC, E5RCSS, E5RHCNR, E5RHCTA, E8RCIC, E8RCNR, E8RCSS, E8RCTA
0389579
 
0389579 CARBURETOR ASSY.
E5RCIC, E5RCSS, E5RHCNR, E8RCIC, E8RCNR, E8RCSS
0391517
 
0391517 CARBURETOR ASSY.
E5RCIC, E5RCSS, E5RHCNR, E5RHCTA, E8RCIC, E8RCNR, E8RCSS, E8RCTA
0391305
CARBURETOR REPAIR KIT
0391305 CARBURETOR REPAIR KIT
E5RCIC, E5RCSS, E5RHCNR, E5RHCTA, E6RCOB, E6RCRM, E8RCIC, E8RCNR, E8RCOB, E8RCRM, E8RCSS, E8RCTA
0390249
 
0390249 CARBURETOR ASSY
E5RCIC, E5RCSS, E8RCIC, E8RCSS
0390691
 
0390691 CARBURETOR ASSY.
E4BRCICI, E4WCIC
0392182
 
0392182 CARBURETOR ASSY., (except SRL model)
E5RHCNR, E5RHCTA, E8RCNR, E8RCTA
0393046
 
0393046 CARBURETOR ASSY., (SRL model only)
E5RHCNR, E5RHCTA, E6RCRM, E8RCNR, E8RCRM, E8RCTA
Back to top