0395139 CARBURETOR ASSY., EVINRUDE
E6RCOB, E6RCRM, E8RCOB, E8RCRM
CARBURETOR
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Beck/Arnley 0395139 Fuel Injection Throttle Body Mounting Gasket
Beck/Arnley Matches OE form, fit and function || Made with high quality materials for durability || Designed for underhood conditions || Packaged in clear plastic for easy visibility and identification of all components || Application specific for this vehicle
Beck/Arnley Matches OE form, fit and function || Made with high quality materials for durability || Designed for underhood conditions || Packaged in clear plastic for easy visibility and identification of all components || Application specific for this vehicle
BRP EVINRUDE entire parts catalog list:
- CARBURETOR » 0395139
E8RCOB, E8RLCOB, E8SRLCOB 1985
E8RCRM, E8RLCRM, E8SRLCRM 1984
Information:
Table 1
J1939 Codes and Description CDL Code and Description Comments
3719-16
High DPF #1 Soot Loading E995 (2)
High DPF #1 Soot Loading The estimated soot load is high. The ECM shuts down the engine when this code becomes active for the first time. The engine can be started and operated. Engine power is gradually derated or maximum rpm will be lowered as the soot load increases.
3719-0
High DPF #1 Soot Loading E995 (3)
High DPF #1 Soot Loading The estimated soot load is high. Engine operation is limited to 60 second intervals when the Caterpillar Electronic Technician (ET) is not communicating with the ECM.
3715-31
DPF Active Regeneration Inhibited Due to Permanent System Lockout E991 (3)
DPF Active Regeneration Inhibited Due to Permanent System Lockout The estimated soot load is high. The engine may not operate properly. Factory passwords are required in order to clear this code.
3714-31
DPF Active Regeneration Inhibited Due to Temporary System Lockout E992 (3)
DPF Active Regeneration Inhibited Due to Temporary System Lockout The engine has been running for10 minutes after the E995 (3) code was activated.
The Cat ET Manual Diesel Particulate Filter Regeneration must be initiated.
Table 2
Associated Diagnostic Trouble Codes
E1045 (2)
E1026 (2)
E1025 (2)
E993 (2)
E1156 (1)
E593 (2)
E1239 (1)
E1026 (1)
E1300 (2)
102-18
3473-31
3474-14
3474-31
3609-15
3703-31
3711-31
3750-31
3716-31 Note: Engine operation must be kept to a minimum in order to minimize the amount of soot that is created. Follow the troubleshooting procedure in order to minimize the amount of engine operation.Troubleshooting Procedure
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Establish communication between Cat® Electronic Technician (ET) and the Electronic Control Module (ECM).
B. Download the "Warranty Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.
C. Look for the following codes:
1. E995 (2) or 3719-16
2. E995 (3) or 3719-0
3. E991 (3) or 3715-31
4. E992 (3) or 3714-31
Codes
Result: A E991 (3) or 3715-31 code is present.
Proceed to Test Step 2.
Result: One of the following codes are present:
1. E995 (2) or 3719-16
2. E995 (3) or 3719-0
3. E992 (3) or 3714-31
Proceed to Test Step 3.
2. E991 (3) or 3715-31 code
A. The E991 (3) or 3715-31 code indicates that the engine has continued to run after repeated warnings and engine shutdowns. The DPF must be replaced. Refer to the Disassembly and Assembly, "Diesel Particulate Filter - Remove and Install (Clean Emissions Module)" for the correct procedure.
DPF
Result: A E991 (3) or 3715-31 code is present.
Repair: Replace the DPF. Refer to the Disassembly and Assembly, "Diesel Particulate Filter - Remove and Install (Clean Emissions Module)" for the correct procedure.
After the DPF has been replaced, clear the E991 (3) or 3715-31 code ( a factory password will be necessary) and proceed to Test Step 3
3. Check for Associated Codes
A. Establish communication between Cat ET and the Electronic Control Module (ECM).
B. Check Cat ET for any associated codes that are listed in Table 2.
Associated Codes
Result: An associated code is active or logged.
Repair: Troubleshoot any codes that are present before continuing with this procedure.
Result: An associated code is not active or logged.
Proceed to Test Step 4.
4. Current Flow through the Heating Element
A. Start the engine.
B. Check the current flow through the heating element. Refer to Systems Operation/Testing and Adjusting, "ARD Nozzle Heater (Current) - Test" for the correct procedure.
Current Flow
Result: The current flow is acceptable.
Proceed to Test Step 5.
Result: The current flow is not acceptable.
Repair: Refer to Troubleshooting, "ARD Nozzle - Test" for the correct procedure.
5. ARD Combustion Air Test
A. Perform the "ARD Air System Service".
Combustion Air Test
Result: The test results are unacceptable.
Repair: Refer to Troubleshooting, "ARD Combustion Air - Test" for information on the test, if necessary. Make the necessary repairs.
Result: The test results are acceptable.
Proceed to Test Step 6.
6. Manual DPF Regeneration
Do not use the cab switch for a stationary regeneration. The service tests provide enhanced diagnostics that are necessary for proper troubleshooting and repair.
A. Start a "Manual DPF Regeneration" in Cat ET.
Manual DPF Regeneration
Result: The "Manual DPF Regeneration" was successful.
Return the engine to service.
Result: The "Manual DPF Regeneration" not was successful.
Repair: Troubleshoot the diagnostic codes that are present.
Contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Parts carburetor EVINRUDE:
0391305
0391305 CARBURETOR REPAIR KIT
E5RCIC, E5RCSS, E5RHCNR, E5RHCTA, E6RCOB, E6RCRM, E8RCIC, E8RCNR, E8RCOB, E8RCRM, E8RCSS, E8RCTA
0393046
0394630
0396363