0435376 CARB. ASSY. EVINRUDE
B25JREUR, BE20SEEDA, BE20SEEUM, BE20SREDA, BE20SREUM, BE25BAEDR, BE25EEDM, BE25EEUB, BE30BAEDE, BE30BAEUD, BE30EEDE, BE30EEUD, E20CREDA, E20CREOR, E20CRERC, E20CRETS, E20EEOR, E20EERC, E20EETS, E25EEOA, E25EERR, E25EETC, E25REDA, E25REOR, E25RERC, E2
CARB
Price: query
Rating:
Compatible models:
B25JREUR
BE20SEEDA
BE20SEEUM
BE20SREDA
BE20SREUM
BE25BAEDR
BE25EEDM
BE25EEUB
BE30BAEDE
BE30BAEUD
BE30EEDE
BE30EEUD
E20CREDA
E20CREOR
E20CRERC
E20CRETS
E20EEOR
E20EERC
E20EETS
E25EEOA
E25EERR
E25EETC
E25REDA
E25REOR
E25RERC
E25RETS
E25TEEDA
E25TEEOR
E25TEERC
E25TEETS
E25TEEUM
E30EEOB
E30EERM
E30EETA
E30REDE
E30REOB
E30RERM
E30RETA
E30TEEDE
E30TEEOB
E30TEERM
E30TEETA
E30TEEUD
E35RERM
E35RETA
SE35REDE
EVINRUDE
BRP EVINRUDE entire parts catalog list:
BE20SEEDA, BE20SELEDA 1996
BE20SEEUM, BE20SELEUM 1997
BE20SREDA, BE20SRLEDA 1996
BE20SREUM, BE20SRLEUM, E20CREUM, E20CRLEUM 1997
BE25BAEDR, BE25BALEDR, BE25BREDC, BE25BRLEDC, HE25RAEDA, SE25RDEDC 1996
BE25EEDM, BE25ELEDM, BE25EREDC, BE25ERLEDC, E25EEDM, E25ELEDM 1996
BE25EEUB, BE25ELEUB, E25EEUB, E25ELEUB 1997
BE30BAEDE, BE30BALEDE 1996
BE30BAEUD, BE30BALEUD, E30REUD, E30RLEUD 1997
BE30EEDE, BE30ELEDE, E30EEDE, E30ELEDE 1996
BE30EEUD, BE30ELEUD, E30EEUD, E30ELEUD 1997
E20CREDA, E20CRLEDA, HE20CREDA, HE20CRLEDA 1996
E20CREOR, E20CRLEOR 1995
E20CRERC, E20CRLERC 1994
E20CRETS, E20CRLETS, TE20CRETS, TE20CRLETS 1993
E20EEOR, E20ELEOR 1995
E20EERC, E20ELERC 1994
E20EETS, E20ELETS 1993
E25EEOA, E25ELEOA 1995
E25EERR, E25ELERR 1994
E25EETC, E25ELETC, TE25ELETC, VE25ELETC 1993
E25REDA, E25RLEDA, HE25REDA, HE25RLEDA 1996
E25REOR, E25RLEOR 1995
E25RERC, E25RLERC 1994
E25RETS, E25RLETS 1993
E25TEEDA, E25TELEDA, HE25TELEDA 1996
E25TEEOR, E25TELEOR 1995
E25TEERC 1994
E25TEETS, E25TELETS 1993
E25TEEUM, E25TELEUM 1997
E30EEOB, E30ELEOB 1995
E30EERM, E30ELERM 1994
E30EETA, E30ELETA, VE30EETA, VE30ELETA 1993
E30REDE, E30RLEDE, HE30REDE, HE30RLEDE 1996
E30REOB, E30RLEOB 1995
E30RERM, E30RLERM 1994
E30RETA, E30RLETA 1993
E30TEEDE, E30TELEDE 1996
E30TEEOB, E30TELEOB 1995
E30TEERM, E30TELERM 1994
E30TEETA, E30TELETA 1993
E30TEEUD, E30TELEUD 1997
E35RERM, E35RLERM 1994
E35RETA, E35RLETA 1993
SE35REDE, SE35RLEDE 1996
Information:
Start By: a. remove valve covers
Do not let the tops of the fuel injection nozzles turn when the fuel lines are loosened. The nozzles will be damaged if the top of the nozzles turn in the body.
1. Use tooling (A) to loosen the nuts on the fuel injection line.2. Remove fuel injection lines (1).3. Disconnect fuel injection line nut (2) from head adapter nut (3).4. Remove adapter nut (3) and the O-ring seal. 5. Remove four bolts (4) that hold rocker arm assembly (5), and remove rocker arm assembly (5).Install Rocker Shaft Assemblies
1. Check the adjustment of the valve bridges. See Install Push Rods, Valve Lifters And Valve Bridges. 2. Loosen all the rocker arm adjusting screws on rocker shaft assembly (5).3. Install rocker shaft assembly (5).4. Clean the bolts that hold the rocker shaft assembly. Put 2P2506 Thread Lubricant on the bolt threads, and install them.5. Be sure the rocker arms and push rods are in alignment before the rocker shaft assembly bolts are tightened.6. Tighten the rocker shaft bolts in the following sequence.a. Tighten bolts (1) through (4) in numerical sequence to a torque of 280 27 N m (210 20 lb.ft.).b. Tighten bolts (1) through (4) in numerical sequence to a torque of 440 20 N m (320 15 lb.ft.).c. Tighten bolts (1) through (4) in numerical sequence again to a final torque of 440 20 N m (320 15 lb.ft.). 7. Install a new O-ring seal on head adapter (7), and put clean engine oil on it.8. Put fuel injection line (8) in position, but do not tighten the nuts.9. Install adapters (7), and connect fuel injection lines (8).10. Connect fuel injection lines (6) to adapters (7).
Do not let the tops of the fuel injection nozzles turn when the fuel lines are tightened. The nozzles will be damaged if the top of the nozzles turn in the body.
11. Use tooling (A) to tighten the fuel injection line nuts to a torque of 41 7 N m (30 5 lb.ft.).12. Adjust the valve clearance settings. The clearance for the intake valve is 0.38 mm (.015 in.). The clearance for the exhaust valves is 0.76 mm (.030 in.). See Valve Clearance Setting in Testing And Adjusting.End By:a. install valve coversDisassemble Rocker Shaft Assemblies
Start By: a. remove rocker shaft assemblies 1. Remove retainer (1) from the end of the shaft.2. Remove the washers and rocker arm (2). 3. Use tool (A) to remove the pin that holds bracket (3) to the rocker arm shaft.4. Remove bracket (3), rocker arm (4) and the spring.5. Remove the remainder of the rocker arms. The center brackets do not have pins.Assemble Rocker Shaft Assemblies
Make sure all parts of the rocker shaft assembly are clean before assembly. 1. Put clean engine oil on shaft (3).2. Install the center springs, rocker arms and bracket.3. Install spring (1), rocker arm (4) and bracket (2).4. Put tape around the shaft on each side of bracket (2) as shown. Put the hole in bracket (2) in alignment with the hole in shaft (3). Put a mark on each piece of tape in alignment with the hole in bracket (2).5. Install pin (5) until it is extended 12.7 1.0 mm (.50 .04 in.) above the surface of bracket (2). Make sure pin (5) is in alignment with the marks on the tape before the pin is installed. Remove the tape.6. Install rocker arm (6), washers (7) and retainer (8). Install enough washers until the end play on each end of the shaft is 0.30 to 1.40 mm (.012 to .055 in.).End By: a. install rocker shaft assemblies
Do not let the tops of the fuel injection nozzles turn when the fuel lines are loosened. The nozzles will be damaged if the top of the nozzles turn in the body.
1. Use tooling (A) to loosen the nuts on the fuel injection line.2. Remove fuel injection lines (1).3. Disconnect fuel injection line nut (2) from head adapter nut (3).4. Remove adapter nut (3) and the O-ring seal. 5. Remove four bolts (4) that hold rocker arm assembly (5), and remove rocker arm assembly (5).Install Rocker Shaft Assemblies
1. Check the adjustment of the valve bridges. See Install Push Rods, Valve Lifters And Valve Bridges. 2. Loosen all the rocker arm adjusting screws on rocker shaft assembly (5).3. Install rocker shaft assembly (5).4. Clean the bolts that hold the rocker shaft assembly. Put 2P2506 Thread Lubricant on the bolt threads, and install them.5. Be sure the rocker arms and push rods are in alignment before the rocker shaft assembly bolts are tightened.6. Tighten the rocker shaft bolts in the following sequence.a. Tighten bolts (1) through (4) in numerical sequence to a torque of 280 27 N m (210 20 lb.ft.).b. Tighten bolts (1) through (4) in numerical sequence to a torque of 440 20 N m (320 15 lb.ft.).c. Tighten bolts (1) through (4) in numerical sequence again to a final torque of 440 20 N m (320 15 lb.ft.). 7. Install a new O-ring seal on head adapter (7), and put clean engine oil on it.8. Put fuel injection line (8) in position, but do not tighten the nuts.9. Install adapters (7), and connect fuel injection lines (8).10. Connect fuel injection lines (6) to adapters (7).
Do not let the tops of the fuel injection nozzles turn when the fuel lines are tightened. The nozzles will be damaged if the top of the nozzles turn in the body.
11. Use tooling (A) to tighten the fuel injection line nuts to a torque of 41 7 N m (30 5 lb.ft.).12. Adjust the valve clearance settings. The clearance for the intake valve is 0.38 mm (.015 in.). The clearance for the exhaust valves is 0.76 mm (.030 in.). See Valve Clearance Setting in Testing And Adjusting.End By:a. install valve coversDisassemble Rocker Shaft Assemblies
Start By: a. remove rocker shaft assemblies 1. Remove retainer (1) from the end of the shaft.2. Remove the washers and rocker arm (2). 3. Use tool (A) to remove the pin that holds bracket (3) to the rocker arm shaft.4. Remove bracket (3), rocker arm (4) and the spring.5. Remove the remainder of the rocker arms. The center brackets do not have pins.Assemble Rocker Shaft Assemblies
Make sure all parts of the rocker shaft assembly are clean before assembly. 1. Put clean engine oil on shaft (3).2. Install the center springs, rocker arms and bracket.3. Install spring (1), rocker arm (4) and bracket (2).4. Put tape around the shaft on each side of bracket (2) as shown. Put the hole in bracket (2) in alignment with the hole in shaft (3). Put a mark on each piece of tape in alignment with the hole in bracket (2).5. Install pin (5) until it is extended 12.7 1.0 mm (.50 .04 in.) above the surface of bracket (2). Make sure pin (5) is in alignment with the marks on the tape before the pin is installed. Remove the tape.6. Install rocker arm (6), washers (7) and retainer (8). Install enough washers until the end play on each end of the shaft is 0.30 to 1.40 mm (.012 to .055 in.).End By: a. install rocker shaft assemblies
Parts carb EVINRUDE:
0435384
0435384 CARB. ASSY.
B25JREUR, BE20SREDA, BE20SREUM, BE25BAEDR, BE30BAEDE, BE30BAEUD, E25JREDC, E25JREOS, E25RWERD