0439619 EVINRUDE CARBURETOR ASSY., Lower


0439619 CARBURETOR ASSY., Lower EVINRUDE BE200CXECM, BE225CXECS, E250CXECD CARBURETOR
0439619 CARBURETOR ASSY., Lower EVINRUDE
Rating:
98

Buy CARBURETOR ASSY., Lower 0439619 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 43961
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

BE200CXECM, BE200TXECM, E200CXECM, E200STLECE, E200TLECM, E200TXECM 1998
BE225CXECS, BE225SLECS, BE225TXECS, E225CXECS, E225CZECS, E225STLECS, E225TXECS, E225TZECS, SE225GLECC, SE225NXECC, SE225NZECC, SE225QXECC, SE225QZECC 1998
E250CXECD, E250CZECD, E250PXECD, E250PZECD 1998

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     8S-2264     Puller Gp     3    Start By:
Remove fuel injection linesNote: Refer to Specifications, ""Engine Design"" for non-specified engine torques.
Illustration 1 g03351476
Remove fuel injection pump drive gear access cover (1) from front housing (2). Note: The cover is secured with adhesive sealant. Use a scraper to separate the cover from the gear case.
Illustration 2 g03349227
Note: After marking the position of the fuel injection pump drive gear (3) , do not rotate the engine crankshaft. Rotating the crankshaft will cause the fuel injection pump to become misaligned.
Place a mark on the fuel injection pump drive gear (3) and the idler gear for installation purposes. Loosen center nut (4) and back out to the end of the fuel injection pump shaft. DO NOT loosen the four bolts (5) that hold the fuel injection pump gear to the hub.
Illustration 3 g03384642
Note: Do not loosen or remove the four bolts (5) retaining the fuel injection pump drive gear (3) to the fuel injection pump hub (3A). Do not disassemble the fuel injection pump drive gear from the hub. Correct fuel injection timing will be difficult or next to impossible to achieve.
Illustration 4 g03349237
Install Tooling (A) onto the end of the fuel injection pump shaft nut (4). Loosen the pump drive gear (3) from the shaft, remove Tooling (A) and remove nut and washer (4) .Note: Fuel injection pump drive gear (3) can be removed from the gear case, however, would be best to let the gear remain in the gear housing.
Illustration 5 g03349431
Locate and highlight the timing mark (9) on the base of fuel injection pump (6) for installation purposes. Make a corresponding mark on the gear case. Unplug the stop solenoid harness assembly. Remove lube oil line (7) from the fuel injection pump and the block assembly. Remove mounting nuts (8) and fuel injection pump (6). Installation Procedure
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
B         Loctite 593 Silicone Sealer        
Illustration 6 g03353182
Position fuel injection pump (6) into the housing and the pump drive gear. Install nuts (8). Line up timing marks (9) if the old fuel injection pump is being reused. If new fuel injection pump is being installed, refer to Testing and Adjusting, "Fuel Injection Timing - Check/Adjust" for the correct fuel injection timing procedures. Install lube oil line (7). Tighten nut (8) to a torque of 23 to 28 N m (204 to 248 lb in).
Illustration 7 g03349475
Make sure that fuel injection pump drive gear (3) is aligned with the idler gear using the reference marks made earlier. Install the washer and nut (4). Tighten nut (4) to a torque of 59 to 69 N m (44 to 51 lb ft) while holding the crankshaft pulley bolt with a socket wrench to prevent the crankshaft from turning.
Illustration 8 g03351683
Apply Tooling (B) on mating surface of cover (1). Install cover (1) on front housing (2). End By: Install fuel injector lines


Parts carburetor EVINRUDE:

0439188
 
0439188 CARBURETOR ASSY., Upper
BE200CXECM, BE200CXEUA, BE225CXECS, BE225CXEUD, E200WPXEEN, E200WPXSIF, E200WPXSSC, E250CXECD, SE200WTPLG, SE200WTPLS
0439189
 
0439189 CARBURETOR ASSY., Lower
BE200CXECM, BE200CXEUA, BE225CXECS, BE225CXEUD, E200WPXEEN, E200WPXSIF, E200WPXSSC, E250CXECD, SE200WTPLG, SE200WTPLS
0439509
 
0439509 CARBURETOR ASSY., Upper
BE200CXECM, BE200CXEUA, BE225CXECS, BE225CXEUD, BE250CXECB, E250CXECD
0439510
 
0439510 CARBURETOR ASSY., Lower
BE200CXECM, BE200CXEUA, BE225CXECS, BE225CXEUD, BE250CXECB, E250CXECD
0439618
 
0439618 CARBURETOR ASSY., Upper
BE200CXECM, BE225CXECS, E250CXECD
0439996
 
0439996 CARBURETOR ASSY., Upper
BE200CXECM, BE225CXECS, E250CXECD
0439997
 
0439997 CARBURETOR ASSY., Lower
BE200CXECM, BE225CXECS, E250CXECD
Back to top