5032424 EVINRUDE CARBURETOR REPAIR KIT

Table 1
Diagnostic Codes Table    
Description     Conditions which Generate this Code     System Response     Procedure    
268-2 Programmed Parameter Fault erratic, intermittent, or incorrect     The Electronic Control Module (ECM) detects that one or more of the programmable parameters have not been programmed.     The engine performance may be affected by unprogrammed parameters. The unprogrammed parameters determine the action that is taken by the ECM. The ECM may use a default torque map or the ECM may limit the engine to low idle.     Program the missing parameter.    
1495-2 Injector Trim Codes Not Programmed     The ECM detects that one or more of the injector trim codes has not been programmed. The ECM has been powered for three seconds.     The code is logged in memory. The engine will start. The ECM will use a default setting of 0000 for an unprogrammed injector trim code.     Program the missing injector trim code.    System configuration parameters are parameters that affect emissions and power of the engine. Default values for the parameters are programmed at the factory. Some parameters may be changed by the customer in order to suit the needs of the specific application. Values for these parameters can be viewed on Caterpillar Electronic Technician (ET). Certain configuration parameters are also stamped on the engine information plate.No password is required for programming a new ECM during the first 100 hours of service life. This 100 hour "free configuration" feature enables the customer to tailor the programmable setpoints to the requirements of the installation. Exceptions are "Fuel Limit" and "Personality Module Mismatch".Note: If the parameters that are protected with the factory passwords are changed, the Caterpillar warranty may be voided.Parameter Table
Table 2
System Configuration Parameters    
Parameter     Default     Range     Password
Required    
Personality Module Interlock             Yes    
ECM
Serial Number             Yes    
Engine Serial Number     00000000     8 alphanumeric numbers     No    
Equipment ID     00000000000000000     17 alphanumeric numbers     No    
Full Load Setting (FLS)     0     -128 to +127     Yes    
Full Torque Setting (FTS)     0     -128 to +127     Yes    
"Fuel Ratio Control Offset (FRC)"     0     -25 to 0     No    
"Rated Fuel Positon (mm)"     14     The minimum rack is based on engine power.     Yes    
Fuel Correction Factor (%)     0     -25 to +25     No    
Low Idle (rpm)     1000     810 to 1000     No    
Droop (%)     0.0     0.0 to 10.0     No    
"Governor Gain Factor"     Engine rating     0 to 39,999     Yes    
"Governor Minimum Stability Factor"     Engine rating     0 to 39,999     Yes    
"Governor Maximum Stability Factor"     Engine rating     0 to 39,999     Yes    
Acceleration Delay on Start-up (sec)     0     0 to 60     No    
Acceleration Rate (rpm/sec)     250     5 to 2000     No    
Programmable Torque Scaling     The minimum rack is based on engine power.     The minimum rack is based on engine power.     Yes    
"Engine Cooling System Configuration"     SCAC     SCAC or JWAC     Yes    
Cold Cylinder Cutout     Disabled     Enabled
Disabled     No    
"Cooldown Engine Speed (rpm)"     900     810 to 1800     No    
"Engine Cooldown Duration (min)"     0     0 to 30     No    
"Engine Prelube Duration (sec)"     0     0 to 210     No    
"Crank Duration (sec)"     0     0 to 60     No    
"Maximum Number of Crank Cycles"     0     0 to 10     No    
"Crank Terminate Speed (rpm)"     400     100 to 500     No    
"Total Tattletale"     0     0 to 255     N/A    
Injector Code (1)     0000     4 numbers     No    
Injector Code (2)     0000     4 numbers     No    
Injector Code (3)     0000     4 numbers     No    
Injector Code (4)     0000     4 numbers     No    
Injector Code (5)     0000     4 numbers     No    
Injector Code (6)     0000     4 numbers     No    
Injector Code (7)     0000     4 numbers     No    
Injector Code (8)     0000     4 numbers     No    
Injector Code (9)     0000     4 numbers     No    
Injector Code (10)     0000     4 numbers     No    
Injector Code (11)     0000     4 numbers     No    
Injector Code (12)     0000     4 numbers     No    Parameter Descriptions
"Personality Module Interlock"
The "Personality Module Interlock" is automatically programmed by the ECM after factory passwords are entered."ECM Serial Number"
The "ECM Serial Number" is stored in the memory of the ECM. The "ECM Serial Number" can be accessed by the use of the service tool."Engine Serial Number"
Program the "Engine Serial Number" to match the engine serial number that is stamped on the engine information plate.Note: When you are requesting factory passwords, always use the engine serial number that is resident in the ECM."Equipment ID"
"Equipment ID" allows the customer to enter a description into the ECM in order to identify the engine. A maximum of 17 characters may be entered in the field. This parameter is only for reference by the customer. This parameter is not required."Full Load Setting (FLS)"
"FLS" is a number that represents the adjustment to the fuel system that was made at the factory in order to fine tune the fuel system. The correct value for this parameter is stamped on the engine information plate. Factory passwords are required."Full Torque Setting (FTS)"
"FTS" is similar to "FLS". Factory passwords are