0394392 CHROME PUMP KIT EVINRUDE
E25ECRS, E25RWCDC, E25RWCOS, E25RWCRD, E25RWCUR, E25RWEDC, E25RWEIM, E25RWENB, E25RWEOS, E25RWERD, E25RWESA, E25RWETE, E25RWEUR, E25RWK, E28ESLCCR, E28ESLCCR, E28ESLCEA, E28ESLCEA, E28ESLCUC, E28ESLCUC, E28ESLEDR, E28ESLEDR, E28ESLEIB, E28ESLEIB, E28
CHROME
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- GEARCASE » 0394392
E25RWCOS, E25RWLCOS 1985
E25RWCRD, E25RWLCRD 1984
E25RWCUR, E25RWLCUR 1987
E25RWEDC, E25RWLEDC, HE25FPO, HE25RSLO 1996
E25RWEIM, E25RWLEIM 1991
E25RWENB, E25RWLENB 1992
E25RWEOS, E25RWLEOS 1995
E25RWERD, E25RWLERD 1994
E25RWESA, E25RWLESA 1990
E25RWETE, E25RWLETE 1993
E25RWEUR, E25RWLEUR, HE25FPV, HE25RSLV, SE25RPLV, SE25RPV 1997
E25RWK, E25RWLK 1989
E28ESLCCR 1988
E28ESLCCR, VE28ESLCCR 1988
E28ESLCEA, VE28ESLCEA 1989
E28ESLCEA 1989
E28ESLCUC 1987
E28ESLCUC 1987
E28ESLEDR 1996
E28ESLEDR 1996
E28ESLEIB 1991
E28ESLEIB 1991
E28ESLENE 1992
E28ESLENE 1992
E28ESLEOC 1995
E28ESLEOC 1995
E28ESLERS 1994
E28ESLERS 1994
E28ESLESM 1990
E28ESLESM, VE28ESLESM 1990
E28ESLETD 1993
E28ESLETD 1993
U25RWA, U25RWLA 1988
VE14RCCS 1988
VE14RCEC 1989
Information:
Table 1
Diagnostic Trouble Codes for the Circuit for Mode Selection
J1939 Code Description Notes
2882-2 Engine Alternate Rating Select : Erratic, Intermittent, or Incorrect The Electronic Control Module (ECM) detects a combination of switch positions for the mode switches that has not been defined.
If equipped, the warning lamp will come on and the ECM will log the diagnostic code.
The ECM will return the engine to the last good mode selection or setting.
The engine will start and the engine will default to the previous mode selection. The engine may operate at reduced speed or reduced power depending on the mode that is selected. Use this procedure to check if the mode selector switch operates correctly.The mode selector switch inputs provide the operator with the ability to select a maximum of four different modes of operation. Different modes of operation can be used giving the operator a means to select the most efficient method of completing the required work.Each mode has a single fuel limit map, a rated speed, and a matched fuel delivery. Each mode also has a specific droop value for throttle 1 and throttle 2.
Table 2
Mode Number Switch 2 Switch 1 Enabled
1 Open Open Y/N
2 Open Closed Y/N
3 Closed Open Y/N
4 Closed Closed Y/N If an open or short circuit condition occurs in the circuit for switch 1 or switch 2, the mode of operation will be different to the mode that was selected by the operator. If the mode of operation is not enabled on the application, a 2882-2 diagnostic code will become active.
Illustration 1 g02129713
Typical schematic for the mode selector switches
Illustration 2 g02129720
View of the pin locations on the P1 connector for the circuit for mode selection
(62) Mode switch 1
(64) Mode switch 2 Test Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch OFF.
Thoroughly inspect the P1 connector. Thoroughly inspect the mode switch connectors, plugs, and interconnections on the harness. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the P1 connector that are associated with the mode selector switches.
Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
Check the harness for abrasions and for pinch points from the battery to the ECM. Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the connectors or the harness and/or replace the connectors or the harness. Ensure that all of the seals are correctly in place and ensure that the connectors are correctly connected.Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair eliminates the fault.STOP
- If the fault has not been eliminated proceed to Test Step 2.Test Step 2. Check the Status of the Mode Selector Switch
Turn the keyswitch to the OFF position.
Connect the electronic service tool to the diagnostic connector.
Turn the keyswitch to the ON position.
Monitor the status screen on the electronic service tool. Cycle the mode switch to the ON position and to the OFF position. Results:
The switch status changes as you cycle the mode switches. When the switch is in the OFF position, the switch is open. When the switch is in the ON position, the switch is closed. - Repair: Verify that the status of the switch changes as the switch is cycled. STOP
The switch status does not change as you cycle the mode switches - There is a fault with the circuit for the mode selector switch. Proceed to Test Step 3.Test Step 3. Insert a Jumper at the Suspect Mode Switch
Turn the keyswitch to the OFF position.
Perform the following procedure to test the circuit of mode selector switch No. 1. Place a jumper wire across the contacts of switch No. 1.
Perform the following procedure to test the circuit of mode selector switch No. 2. Place a jumper wire across the contacts of switch No. 2.
Turn the keyswitch to the ON position. Monitor the status screen on the electronic service tool. Connect the jumper wire and then disconnect the jumper wire. Expected Result:When the jumper wire is connected, the switch should be in the CLOSED position.Results:
When the jumper wire is connected, the switch is in the CLOSED position. - Repair: Verify that the jumper wire has been removed. The suspect mode selector switch is faulty. Replace the switch and verify that the repair has eliminated the fault.STOP
When the jumper wire is connected, the switch is in the OPEN position - Proceed to Test Step 4.Test Step 4. Measure the Voltage at the Switch
Turn the keyswitch to the OFF position.
Use the electronic service tool to turn both of the mode switches to the ON position.
Turn the keyswitch to the ON position.
Measure the voltage from the input or the output of each mode switch to a suitable ground. Expected Result:For 12 V systems, the measured voltage should be a constant 11.0 to 13.5 VDC.For 24 V systems, the measured voltage should be a constant 22.0 to 27.0 VDC.Results:
OK - The measured voltages are within the expected range. The wiring between the mode switches and switched battery+ is OK. Proceed to Test Step 5.
Not OK - One of the measured voltages is not within the expected range. The fault is in the wiring between switched battery+ and the mode switch with the incorrect voltage.Repair: Repair the faulty wiring or replace the faulty wiring.Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair has eliminated the fault.STOPTest Step 5. Measure the Voltage at the ECM
Turn the keyswitch to the OFF position.
Use the electronic service tool to turn both of the mode switches to the ON position.
Turn the keyswitch to the ON position.
Measure the voltage from P1:62 to a suitable ground.
Measure the voltage from P1:64 to a suitable ground. Expected Result:For 12 V systems, the measured voltage should be a constant 11.0 to 13.5 VDC.For 24 V systems, the measured voltage should be a constant 22.0 to 27.0 VDC.Results:
OK - The measured voltages are within the expected range. There
Parts chrome EVINRUDE:
0394415
0394415 CHROME PUMP KIT
E20CRCEM, E20CREIE, E20CREND, E20CRERC, E20CRESB, E20CRETS, E20ECEM, E20EEIE, E20EEND, E20EERC, E20EESB, E20EETS, E25ECEB, E25EEID, E25EENS, E25EERR, E25EESE, E25EETC, E25RCEM, E25REIE, E25REND, E25RERC, E25RESB, E25RETS, E25RWEDC, E25RWEOS, E25RWEUR