0308078 CLAMP, Cable to boat EVINRUDE
115393M, 115493B, 115593, 115693D, 135383M, 135443B, 135543E, 135643D, 200640S, 50302R, 50442M, 50542B, 55642E, 65372R, 70442M, 70572B, 70673D, 75542B, 75642D, 85393M, 85493B, 85593E, 85693D
CLAMP
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- REMOTE CONTRO » 0308078
- REMOTE CONTROL
115593 1975
115693D, 115693G, 115699D, 115699G 1976
135383M 1973
135443B, 135483B, 135489B 1974
135543E, 135583E, 135589E 1975
135643D, 135643G, 135683D, 135683G 1976
200640S, 200649S 1976
50302R, 50303R, 50372R, 50373R 1973
50442M, 50443M, 50472M, 50473M 1974
50542B, 50543B, 50572B, 50573B 1975
55642E, 55643E, 55672E, 55673E 1976
65372R, 65373R 1973
70442M, 70443M, 70472M, 70473M 1974
70572B, 70572E, 70573B, 70573E 1975
70673D 1976
75542B, 75543B 1975
75642D, 75643D 1976
85393M 1973
85493B 1974
85593E 1975
85693D, 85693G, 85699G 1976
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 5P-7306 Shaft Housing 1
5P-7305 Engine Turning Tool 1
B 136-4632 Timing Pin 1
268-1966 Adapter 1
C 1P-2320 Combination Puller 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all hoses, on all hose assemblies and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. Plugging all hose assemblies and tube assemblies helps to prevent fluid loss and also helps to keep contaminants from entering the system.
Do not disconnect the air lines until the air pressure in the system is at zero. If hose is disconnected under pressure it can cause personal injury.
Release the pressure from the air system. Refer to the Original Equipment Manufactures (OEM) for the correct procedure.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
If the engine is equipped with a hydraulic pump on the rear of the air compressor, remove the hydraulic pump. Refer to the OEM for the correct procedure.
Use Tooling (A) to rotate the crankshaft so that number one piston is at the top center position on the compression stroke. Refer to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.Note: The air compressor must be timed with the engine to minimize engine vibration.
Illustration 1 g01966313
Typical example
Remove plug (2) from the cylinder block. Remove O-ring seal (1) from the plug.
Install Tooling (B) into Hole (X) in the cylinder block. Use Tooling (B) to lock the crankshaft in the correct position.Note: Do not use excessive force to install Tooling (B). Do not use Tooling (B) to hold the crankshaft during repairs.
Illustration 2 g03360856
Illustration 3 g01965121
Typical example
Slide hose clamps along coolant hose (3) and coolant hose (4). Disconnect coolant hose (3) and coolant hose (4) from air compressor (6).
Disconnect the air lines from port (5) (not shown) and air lines from port (7). Refer to the OEM for the correct procedure.
Remove banjo bolt (9) and sealing washers from air compressor (6).
Remove bolt (10) and bolt (12) from support bracket (11) and remove the support bracket.
Support air compressor (6) and remove nuts (15). Remove the air compressor from front housing (8).
If necessary, remove studs (14) from front housing (8).
If necessary, remove bolts (17) and remove plate (16). Remove O-ring seal (13) from plate (16).
Illustration 4 g01964860
Typical example
Remove O-ring seal (21) from air compressor (6).
If necessary, follow Step 15.a through Step 15.b to remove gear (18) from the crankshaft of the air compressor.
Use a suitable tool to prevent the shaft of the compressor from rotating. Remove nut (20) and remove spring washer (19).
Use Tooling (C) to remove gear (18) from the crankshaft of the air compressor.
Illustration 5 g03360857
If n
Parts clamp EVINRUDE:
0310441
0310441 CLAMP,Sensor rectifier
100193A, 100293R, 100882B, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 175740S, 25702H, 25802C, 33002M, 33802M, 33902A, 35602G, 40202E, 40304D, 40504C,
0310503
0310503 CLAMP,Shift leads
100882B, 33002M, 33802M, 4706B, 4806E, 50172S, 50202C, 50302R, 50442M, 50542B, E40RWCDB, E40RWCOM, E40RWCRA
0309040
0309040 CLAMP,Temperature switch lead
100193A, 100293R, 100882B, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 40052A, 40072A, 40202E, 40304D, 40404S, 40504C, 40604A, 40852A, 40872A, 40952R, 40972R, 50172S, 50
0311339
0311339 CLAMP,Motor cable & voltage regulator lead
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 150940C, 35602G, 40504C, 40604A, 60072B, 60172C, 65272S, 70442M, 70572B, 70673D, 70773S, 70873C, 75542B, 75642D, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E, C155WTLM, E150ANCRS, E150C
0278848
0278848 CLAMP ASSEMBLY, Port
100193A, 115083D, 115983E, 125183C, 125283R, 55872A, 55972A, 60072B, 60172C, 65272S, 65832B, 70442M, 70572B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0316014
0316014 CLAMP, Retainer
100990S, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 50172S, 50202C, 50302R, 50442M, 50542B, 55642E, 55772D, 85393M, 85493B, 85593E, 85693D
0317755
0317755 CLAMP, Stator lead crankcase head
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 135383M, 135443B, 135543E, 135643D, 15404G, 15504C, 15604A, 35602G, 50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55874S, 65372R, 70442M, 70572B, 7
0318508
0318508 CLAMP, Throttle and shaft cable
115393M, 115493B, 115593, 135383M, 135443B, 135543E, 85393M, 85493B, 85593E