5040735 EVINRUDE CLAMP BRACKET


5040735 CLAMP BRACKET EVINRUDE B15R4AAA, B15R4AAB CLAMP
5040735 CLAMP BRACKET EVINRUDE
Rating:
13

Buy CLAMP BRACKET 5040735 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Compatible models:

B15R4AAA   B15R4AAB   EVINRUDE

BRP EVINRUDE entire parts catalog list:

B15R4AAA, B15RL4AAA, E15R4AAA, E15RL4AAA 2012
B15R4AAB, B15RL4AAB, B15TE4AAA, B15TE4AAB, B15TEL4AAA, B15TEL4AAB, E15R4AAB, E15RL4AAB, E15TE4AAA, E15TE4AAB, E15TEL4AAA, E15TEL4AAB 2012

Information:

1. Remove brackets (1) and (2) from the engine. 2. Use Tool (A) to remove the camshaft drive gears from the camshafts.
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact the skin.
3. Drain the oil from the oil pan.4. Remove all the bolts that hold the oil pan to the engine. Install two 3/8 "-16 NC Guide Bolts in each side of the oil pan. Fasten chains and a suitable lifting device to the engine and lift the engine approximately 12 mm (0.5 in) off of the oil pan. Put two 1/4 50 mm wide x 100 mm long x 6 mm thick (2 in wide x 4 in long in thick) Plates in position between the cylinder block and the oil pan on each side of the engine. Lower the engine on the plates and remove the chains and lifting device. The weight of the engine is approximately 5443 kg (12,000 lb). 5. Use Tool (B) to fasten chains and a suitable lifting device to the flywheel housing. Remove the bolts and remove flywheel housing (3) from the engine. The weight of the housing is 245 kg (540 lb). 6. Remove O-ring seal (4) from the engine block.Install Flywheel Housing
1. Install O-ring seal (1) on the engine block and put clean engine oil on it.2. Put the flywheel housing gasket in position on the rear of the engine block. 3. Install two 5/8 "-11 NC Guide Bolts (2) in the engine block. 4. Fasten chains and a suitable lifting device to flywheel housing (3) with Tool (A). Put the housing in position on the guide bolts. Install the bolts to hold the housing in position and tighten the bolt evenly. Remove the guide bolts and install the remainder of the bolts.5. Cut the flywheel housing gasket even with the bottom of the cylinder block.6. Fasten chains and a suitable lifting device to the engine and lift the engine enough to remove the plates between the cylinder block and the oil pan. The weight of the engine is approximately 5443 kg (12,000 lb). If the oil pan gasket is damaged, the engine will have to be removed from the oil pan to make a replacement of the gasket. Lower the engine on the oil pan and remove the guide bolts from the oil pan. Install all of bolts that hold the oil pan to the engine. 7. Put cam shaft drive gears (4) in position on the ends of the camshaft. Install the plate and tachometer drive adapter assembly to hold the gears in position. Tighten the bolts evenly to a torque of 100 15 N m (75 11 lb ft). Hit the plate and adapter assembly with a hammer and tighten the bolts again to the same torque. Do this until the torque does not change. 8. Install brackets (5) and (6) on the engine. Any time the rear crankshaft seal and wear sleeve are removed, a new seal and sleeve must be installed.End By:a. install crankshaft rear seal and wear sleeveb. install exhaust elbow


Parts clamp EVINRUDE:

0348839
*CLAMP, 17mm
0348839 *CLAMP, 17mm
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
5040242
 
5040242 Clamp 6.5-67P
B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4INS, B15TE4INS, B3R4AAA, B4R4AAA, B4R4INS, B6R4AAA, B6R4INS, E15R4INS
5040059
*Clamp, 6.5-14
5040059 *Clamp, 6.5-14
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
5040014
 
5040014 Clamp 6.5-47.5P
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
5040358
CLAMP SCREW KIT
5040358 CLAMP SCREW KIT
B10EL4AAA, B10EL4AAB, B10EL4INS, B15R4AAA, B15R4AAB, E10EL4INS, E10TEL4AAB
5040736
 
5040736 CLAMP BRACKET
B15R4AAA, B15R4AAB
Back to top