0385911 CONNECTING ROD ASSY EVINRUDE
115493B, 115593, 115693D, 135443B, 135543E, 135643D, 200640S, 85493B, 85593E, 85693D
CONNECTING
Price: query
Rating:
Number on catalog scheme: 26
Compatible models:
BRP EVINRUDE entire parts catalog list:
- CRANKSHAFT & PISTON » 0385911
115693D, 115693G, 115699D, 115699G 1976
135443B, 135483B, 135489B 1974
135543E, 135583E, 135589E 1975
135643D, 135643G, 135683D, 135683G 1976
200640S, 200649S 1976
85493B 1974
85593E 1975
85693D, 85693G, 85699G 1976
Information:
Illustration 1 g00622804
(1) Crankcase breathers
(2) Fumes filter The crankcase breather helps to prevent a buildup of pressure in the crankcase. Some of the oil from the fumes that are produced in the crankcase is collected in the breather elements. The fumes travel to the fumes filter. The filter separates the remaining oil from the air. The oil is circulated back into the engine oil sump. The air is circulated back into the engine for combustion.If the crankcase breather is not maintained on a regular basis, the crankcase breather will become plugged. A plugged crankcase breather will cause excessive crankcase pressure that may cause crankshaft seal leakage. The breather elements may be cleaned. The fumes filter element must be replaced.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Cleaning the Crankcase Breathers
Illustration 2 g00927941
Loosen clamps (1). Slide the clamps onto tube (2).
Loosen clamps (3). Remove both breathers as a unit.
Loosen clamp (4). Remove the breather.
Illustration 3 g00927969
Remove O-ring seals (5) from the valve covers. Discard the O-ring seals.
Illustration 4 g00927971
Remove two clamps (7). Remove both breathers from hose tee (8). Inspect the hose tee for cracks. If the tee is cracked, discard the old tee and obtain a new tee for installation.
Remove clamp (9). Remove hose (10). Inspect the hose for cracks. If the hose is cracked, discard the old hose and obtain a new hose for installation.
Clean the breather elements with clean, nonflammable solvent. Turn the breathers upside-down in order to inspect the condition of the breather elements. If the breather elements remain contaminated after the cleaning, discard the breathers and obtain new breathers. Do not attempt to disassemble the breathers.Allow the breather elements to dry before installation.Note: Coat the rubber parts with clean engine oil or petroleum jelly in order to make installation easier.
Place clamp (9) on hose (10). Install the breather into the hose. Tighten the clamp. Note: To find the proper torques for the hose clamps, see Specifications, SENR3130, "Torque Specifications", "Hose Clamps".
Place clamps (7) over the parts of hose tee (8) that will receive breathers (6). Install the breathers into the tee. Tighten the clamps.
Coat new O-ring seals (5) with clean engine oil. Place the O-ring seals on the valve covers.
Place clamps (3) and clamp (4) around the parts of the breathers that will be attached to the valve covers. Install the breathers. Tighten the clamps.
Place clamp (1) on the part of the hose tee that will receive tube (2). Install the tube. Tighten the clamp. Replacing the Fumes Filter Element
Illustration 5 g00622954
(1) Bolt
(2) Canister
(3) Element
Loosen four bolts (1).
Remove canister (2).
Discard element (3).
Place a new element into the canister. Install the canister.
Tighten the bolts.