0435895 EVINRUDE CONNECTING ROD ASSY.


0435895 CONNECTING ROD ASSY. EVINRUDE BE25ARECA, BE25AREDC, BE25AREUR, BE35ARECR, BE35AREDS, BE35AREEA, BE35AREUC, BE35ARSIB, BE35ARSSM, SE35RWECS CONNECTING
0435895 CONNECTING ROD ASSY. EVINRUDE
Rating:
8

Buy CONNECTING ROD ASSY. 0435895 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

BRP EVINRUDE entire parts catalog list:

BE25ARECA, BE25ARLECA, BE25KECA, BE25KLECA, BE25QLECA, E25KLECA, E25QLECA, E25RMECA, E25RMLECA, E25TKECA, E25TKLECA 1998
BE25AREDC, BE25ARLEDC, BE25KEDC, BE25KLEDC, BE25QLEDC, E25KLEDC, E25QLEDC, E25RMEDC, E25RMLEDC, E25TKEDC, E25TKLEDC 1996
BE25AREUR, BE25ARLEUR, BE25KEUR, BE25KLEUR, BE25QLEUR, E25KLEUR, E25QLEUR, E25RMEUR, E25RMLEUR, E25TKEUR, E25TKLEUR 1997
BE35ARECR, BE35ARLECR, BE35KECA, BE35KLECA, BE35QLECA, E35KLECA, E35QLECA, E35TKLECA 1998
BE35AREDS, BE35ARLEDS, BE35KEDC, BE35KLEDC, BE35QLEDC, E35KLEDC, E35QLEDC, E35RMLEDC, E35TKLEDC, HE35RMLEDC 1996
BE35AREEA, BE35KEEM 1999
BE35AREUC, BE35ARLEUC, BE35KEUR, BE35KLEUR, BE35QLEUR, E35KLEUR, E35QLEUR, E35RMLEUR, E35TKLEUR, HE35RMLEUR 1997
BE35ARSIB, BE35KSIE 2001
BE35ARSSM, BE35KSSB 2000
SE35RWECS, SE35RWLECS 1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2 Start By:
Install the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chocks (Front and Rear) - Remove and Install".
Install the truck body retaining cable. Refer to Disassembly and Assembly, "Truck Body Retaining Cable - Remove and Install".
Remove the ambient air temperature sensor. Refer to Disassembly and Assembly, "Temperature Sensor (Ambient Air) - Remove".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hot coolant, steam and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove cooling system pressure cap slowly to relieve pressure only when engine is stopped and cooling system pressure cap is cool enough to touch with your bare hand.Do not attempt to tighten hose connections when the coolant is hot, the hose can come off causing burns.Cooling System Coolant Additive contains alkali. Avoid contact with skin and eyes.
Note: Put identification marks on all wire harnesses and cable assemblies for installation purposes.
Position a suitable container under the radiator drain valves in order to contain the coolant for storage or disposal. Drain the coolant below the level of the expansion tank. The capacity of the radiator is 662 L (175 US gal).
Install caps and plugs on all openings in order to prevent dirt or debris from entering the system. Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Illustration 1 g00570735
Put identification marks on three bolts (1) for installation purposes. Remove three bolts (1) and the washers that hold cover (4) to hood assembly (2) and expansion tank assembly (3). Repeat this procedure on the remaining side of expansion tank assembly (3).
Raise the front hood assembly and the rear hood assembly.
Illustration 2 g00570736
Disconnect hose assembly (5) from expansion tank assembly (3). Repeat this procedure on the remaining side of expansion tank assembly (3).
Illustration 3 g00570737
Remove four bolts (6) and the washers that hold tube assembly (7) to expansion tank assembly (3). Place tube assembly (7) and the rectangular seal aside.
Illustration 4 g00570738
Remove four bolts (8) and the washers that hold tube assembly (9) to expansion tank assembly (3). Place tube assembly (9) and the rectangular seal aside.
Illustration 5 g00570739
Disconnect wire harness (10) at the electrical connection. Repeat this procedure for the wire harness on the remaining side.
Illustration 6 g00570741
Remove nine bolts (11) and the washers that hold hood assembly (2) to cowling assembly (12).
Illustration 7 g00570742
Attach Tooling (A) to hood assembly (2), as shown. Position a suitable lifting device to Tooling (A). Secure the lifting device to a hoist.
Illustration 8 g00570745
Remove cotter (13) and the washer that holds prop assembly (15) to bracket assembly (14).


Back to top