0383677 EVINRUDE COVER ASSY., Air entrance


0383677 COVER ASSY., Air entrance EVINRUDE 100193A, 100293R, 115083D, 115393M, 115983E, 85093B, 85193A, 85293R, 85393M, 85993E COVER
0383677 COVER ASSY., Air entrance EVINRUDE
Rating:
73

Buy COVER ASSY., Air entrance 0383677 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 43
 

BRP EVINRUDE entire parts catalog list:

100193A, 100193C 1971
100293R 1972
115083D 1970
115393M 1973
115983E, 115983S 1969
85093B, 85093D 1970
85193A, 85193H 1971
85293R 1972
85393M 1973
85993E, 85993M, 85993S 1969

Information:

Start By:a. disassemble governorb. remove fuel injection pumps FLUID SPILLAGE CONTAINMENTCare must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "Tools And Shop Product Guide", NENG2500, for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. 1. Remove rack (1) from the fuel pump housing. 2. Remove six lifters (2) from the fuel pump housing. Put identification marks on the lifters for installation purposes. 3. Remove camshaft (3) from the fuel pump housing. It may be necessary to use a soft hammer to push the camshaft out of the governor end of the fuel pump housing. 4. Remove races (4) and bearing (5) from the camshaft. Remove ring (6) if necessary. 5. Remove rack bearing (7) from both ends of the housing and dowel (8) if necessary. 6. Use Tooling (A), and remove three camshaft bearings (9). 7. Remove the bolts, cover (10) and the gasket. 8. Remove pins (12), the seal and dowels (11) if necessary. Pins (12) must be pushed from the inside out.Assemble Fuel Injection Pump Housing
1. Clean and inspect all parts. Make a replacement of all parts that are worn or damaged. 2. Lubricate the seal with clean engine oil, and install pin (12). Pin (12) must protrude into the pump bore 2.15 .05 mm (.085 .002 in).3. Install dowel (11) so that it protrudes into the pump bore 1.93 0.05 mm (.076 .002 in). 4. Install the gasket, cover (10) and the bolts. 5. Install the rack bearing with Tooling (B). Install the bearing until the driver comes in contact with the plate. The bearing should be installed to a depth of 83.0 0.5 mm (3.27 .02 in)from the fuel pump mounting face. 6. Measure rack bearing (7). Dimension (X) must be 11.178 0.05 mm (.4400 .002 in). Diameter (W) must be 12.767 0.058 mm (.5026 .0022 in). 7. Install dowel (8). Dowel (8) must protrude 6.0 0.5 mm (.24 .02 in)from the fuel pump housing face.8. Install the rear rack bearing with Tooling (C) to a depth of 7.16 0.13 mm (.282 .005 in)below the fuel pump housing surface. The inside diameter of the rear rack bearing must be 12.746 0.045 mm (.5018 .0017 in). 9. Use Tooling (D), and install three camshaft bearings (9). Oil holes (13) in the camshaft bearings must be positioned 30 3 degrees above the horizontal centerline toward the engine side of the fuel pump housing. The outer bearings must be installed 1.0 0.5 mm (0.04 0.02 in)below the surface marked (Z). The inner bearing must be installed 218.0 0.3 mm (8.58 .012 in)below the front surface (Y). Diameter (XX) must be 68.339 0.038 mm (2.6905 .0015 in)after assembly. 10. Install ring (6) races (4) and bearing (5) on the camshaft. 11. Lubricate cam bearings (9) and the camshaft bearing journals with clean engine oil.12. Install camshaft (3) into the fuel pump housing.
The notch in the lifter must be in line with the dowel in the lifter bore. The lifter must slide up and down freely in the bore. If it does not, check the dowel for proper installation depth.
13. Lubricate lifters (2) with clean engine oil, and install them in their original lifter bores. 14. Lubricate the rack bearings and rack (1) with clean engine oil.
The rack must slide freely in the rack bearings after installation.
15. Install rack (1). The flat on the rack must line up with the flat on the front rack bearing.End By:a. install fuel injection pumpsb. assemble governor


Parts cover EVINRUDE:

0313586
 
0313586 COVER,High tension lead
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 55872A, 55972A, 60072B, 60172C, 65832B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0580339
COVER & TERMINAL SPRING
0580339 COVER & TERMINAL SPRING
100193A, 1002R, 100882B, 115083D, 115983E, 125183C, 18002C, 1802S, 18102S, 18802A, 18902B, 1902C, 2102A, 25002C, 25102S, 25902B, 33002M, 33802M, 33902A, 3802A, 40052A, 4006E, 40072A, 40102B, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, 4106D, 4902
0313964
 
0313964 COVER,Water passage
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 65832B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0383952
 
0383952 COVER, Terminal board
115083D, 115983E, 85093B, 85993E
0315279
 
0315279 COVER, Cylinder head
100193A, 100293R, 115083D, 115983E, 125183C, 125283R, 85093B, 85193A, 85293R, 85993E
0314849
 
0314849 COVER, Exhaust inner
100193A, 100293R, 115083D, 115983E, 125183C, 125283R, 85093B, 85193A, 85293R, 85993E
0385832
 
0385832 COVER ASSY., Thermo hsg.
115393M, 115493B, 115593, 115693D, 115793S, 135383M, 135443B, 135543E, 135643D, 85393M, 85493B, 85593E, 85693D
0385516
COVER AND PIN ASSY
0385516 COVER AND PIN ASSY
115393M, 115493B, 115593, 115693D, 115790S, 115793S, 135383M, 135443B, 135543E, 135643D, 50302R, 50442M, 65372R, 70442M, 70572B, 85393M, 85493B, 85593E, 85693D
Back to top