0390131 EVINRUDE COVER, Rear, plastic

Table 1
Diagnostic Codes
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
2813-5 3239-5 Air Shutoff Relay : Current Below Normal The code is logged.
2813-6 3239-6 Air Shutoff Relay : Current Above Normal The code is logged.
3667-2 E2088 (1) Engine Air Shutoff Status : Erratic, Intermittent, or Incorrect The inlet air shutoff valve switch has been used, but the inlet air shutoff valve feature is set as "Disabled" in the configuration parameters.
3667-31 E2087 (3) Engine Air Shutoff Status The engine air shutoff valve has been activated. The engine was shut down and injection is disabled. Perform a key cycle and reset the air inlet shutoff system.
Follow the troubleshooting procedure in order to identify the root cause of the problem. Note: The "Air Shutoff" parameter must be set to "Enabled" in order for the ECM to energize the air shutoff solenoid.Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Diagnostic Trouble Codes
A. Establish communication between Cat® Electronic Technician (ET) and the Electronic Control Module (ECM) . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Determine if a code is active or logged.
Diagnostic Code
Result: A 3667-31, or E2087 (3) code is active or logged, or the air inlet shutoff valve is not working properly.
Proceed to Test Step 2.
Result: A 3239-5 or 2813-5 code is active or logged.
Proceed to Test Step 11.
Result: A 3239-6 or 2813-6 code is active or logged.
Proceed to Test Step 12.
Result: A 3667-2 or E2088 (1) code is active or logged.
Proceed to Test Step 13.
2. Perform the "Air Inlet Shutoff Override"
A. Turn the key switch to the OFF position.
B. Connect Cat ET to the service tool connector.
C. Turn the key switch to the ON position.
D. Place the transmission in NEUTRAL.
If the engine will not start, check the air inlet valve to ensure that the valve is not stuck closed.
E. Start the engine. Increase the engine speed to 1500 rpm 100 rpm.
F. Access the "Air Inlet Shutoff Override" in the "Diagnostic Tests" under the "Diagnostics" menu in Cat ET.
G. Start the test.
H. Wait for the engine to stop.
I. Stop the test.
Test
Result: The engine is shut down when the "Air Inlet Shutoff Override" is activated. The air inlet shutoff is working correctly.
Repair: Reset the air inlet shutoff system. Proceed to Test Step 3.
Result: The engine did not shut down.
Proceed to Test Step 5.
3. Check the Air Inlet Shutoff Switch
A. Turn the key switch to the ON position.
B. Connect Cat ET to the service tool connector.
C. Use Cat ET to monitor the status for the air inlet shutoff switch while the switch is depressed.
Switch Works Correctly
Result: The status of the switch changed in Cat ET.
The inlet air shutoff switch is operating properly.
Return to service.
Result: The status of the switch did not change in Cat ET.
Proceed to Test Step 4.
4. Check the Circuit to the Air Inlet Shutoff Switch
A.Turn the key switch to the OFF position.
B. Remove the air inlet shutoff switch.
C. Turn the key switch to the ON position.
D. Connect Cat ET to the service tool connector.
E. Short the terminals of the air inlet shutoff switch together. This will simulate the switch being closed.
F. Use Cat ET to monitor the status for the air inlet shutoff switch while the short is in place.
Circuit
Result: The status changed in Cat ET.
The wiring is OK. The switch is not working properly.
Repair: Replace the air inlet shutoff switch. Verify that the repair eliminates the problem.
Result: The status did not change in Cat ET.
There is a problem with the wiring between the ECM and the air inlet shutoff switch.
Repair: Inspect the wiring between the ECM and the air inlet shutoff switch. Repair the wiring or replace the wiring. Verify that the repair eliminates the problem.
5. Check the Transmission Neutral Switch
A. Verify that the transmission neutral switch is wired correctly.
If a transmission neutral switch is installed, the transmission must be in neutral.
B. Turn the key switch to the ON position.
C. Connect Cat ET to the service tool connector.
D. Monitor the status for the "Transmission Neutral Switch" while the transmission is in neutral. The status should be ON.
Transmission Neutral Switch
Result: The status of the transmission neutral switch is ON.
Proceed to Test Step 6.
Result: The status of the transmission neutral switch is OFF.
Repair: Refer to Troubleshooting, "Neutral Switch Circuit - Test".
6. Inspect Electrical Connectors and Wiring
A. Turn the key switch to the OFF position.
B. Thoroughly inspect the J2/P2 ECM connector and all other connectors in the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Perform a 45 N (10 lb) pull test on the wires that are associated with the air inlet shutoff system.
D. Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
E. Check the harness and wiring for abrasion and for pinch points from the components back to the ECM.
Connectors
Result: All the wires and connections are OK.
Proceed to Test Step 7.
Result: There is a problem with the wiring.
Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are coupled.
Verify that the repair eliminates the problem.
Illustration 1 g00850138
Typical air inlet shutoff solenoid
Table 3
Troubleshooting Test Steps Values Results
7. Check the Supply Voltage to the Air Inlet Shutoff Solenoid
A. Connect Cat ET to the service tool connector.
B. Turn the key switch to the ON position.
C. Perform the "Air Inlet Shutoff Override" test in Cat ET.
D. Measure the voltage across the two terminals of the air inlet shutoff solenoid.
5 VDC
Result:The voltage is within 5 VDC of battery voltage when the test is active. The ECM is properly controlling the relay for the air inlet shutoff solenoid, but the air inlet shutoff solenoid is not working.
Repair: Replace the air inlet shutoff solenoid. Verify that the repair eliminates the problem.
Result: The voltage is not within 5 VDC of battery voltage when the test is active. The air inlet shutoff solenoid is not receiving the correct signal.
Proceed to Test Step 8.
8. Check the Signal Voltage