0311356 EVINRUDE CRANKSAHFT


0311356 CRANKSAHFT EVINRUDE 33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R CRANKSAHFT
0311356 CRANKSAHFT EVINRUDE
Rating:
69

Buy CRANKSAHFT 0311356 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$73.19
 

07-09-2017

APDTY: APDTY
APDTY 0311356 Parking Brake Cable
Meets Or Exceeds OEM Specs||Factory OEM Fit Form And Function
Number on catalog scheme: 4
 

BRP EVINRUDE entire parts catalog list:

33002M, 33003M, 33052M, 33053M 1970
33802M, 33802R, 33803M, 33803R, 33852M, 33852R, 33853M, 33853R 1968
33902A, 33903A, 33952A, 33953A 1969
40002A, 40003A 1970
40052A, 40053A 1970
40072A, 40073A 1970
40102B, 40102G, 40103B, 40103G, 40152B, 40152G, 40153B, 40153G 1971
40202E, 40203E, 40252E, 40253E 1972
40304D, 40305D, 40354D, 40355D 1973
40802A, 40802D, 40802S, 40803A, 40803D, 40803S 1968
40852A, 40852C, 40852D, 40852S, 40853A, 40853C, 40853D, 40853S 1968
40872A, 40872C, 40872D, 40873A, 40873C, 40873D 1968
40902R, 40903R 1969
40952R, 40953R 1969
40972R, 40973R 1969

Information:

Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps    Values    Results    
1. Excessive Idle or High Load
A. Use Caterpillar Electronic Technician (ET) to check the Current Totals for excessive idle time and/or for a high load factor. These factors would be indicative of poor operating habits.
   
Idle time or load
   
Result: The idle times or load was excessive.
Reduce idle times or load.
Result: The idle times or load was not excessive.
Proceed to Test Step 2.
   
2. Diagnostic Codes
A. Check for logged diagnostic codes or active diagnostic codes. If a diagnostic code is logged or active refer to Troubleshooting, "Diagnostic Trouble Codes" for more information.
   
Codes
   
Result: There are logged or active diagnostic codes.
Troubleshoot any logged or active diagnostic codes before continuing with this procedure. Refer to Troubleshooting, "Diagnostic Trouble Codes" for more information.
Result: There are no logged or active diagnostic codes.
Proceed to Test Step 3.
   
3. Fuel Quality
A. The grade of the fuel affects the rate of fuel consumption. Refer to the engines Operation and Maintenance Manual for additional information.
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation.
   
Fuel quality
   
Result: The fuel quality meets specifications.
Proceed to Test Step 4.
Result The fuel quality does not meet specifications.
Replace the fuel with fuel that meets specifications.
   
4. Calibration Procedure of the Engine Speed/Timing
A. Perform a speed/timing sensor calibration. Refer to the calibration procedure Troubleshooting, "Timing - Calibrate".
   
Calibration
   
Result The speed timing calibration was performed.
Proceed to Test Step 5.
   
5. Unstable Injection Actuation System
A. Check for correct installation of the J1/P1 and J2/P2 Electronic Control Module (ECM) connectors and the injector connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
C. Perform the "Cylinder Cutout Test" on Cat ET in order to identify any injectors that might be misfiring. Refer to Troubleshooting, "Injector Solenoid - Test".
   
Injection actuation
   
Result The tests completed successfully.
Proceed to Test Step 6.
Result The tests did not complete successfully.
Make the necessary repairs. Verify that the repair resolved the problem.
   
6. Restriction in the Air Inlet and Exhaust
A. Inspect the air filter for a restriction.
B. Check the air inlet and exhaust system for restrictions and/or for leaks.
   
Restrictions
   
Result There are restrictions in the air inlet or exhaust system.
Remove or repair the restrictions.
Result There are no restrictions in the air inlet or exhaust system.
Proceed to Test Step 7.
   
7. Check for Damaged Accessory Equipment
A. Check all accessory equipment for problems that may create excessive load on the engine.
   
Accessory equipment
   
Result There is damaged accessory equipment.
Remove or repair the accessory equipment.
   Complete the procedure in the order in which the steps are listed. If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Back to top