5001965 CYL & C/C Assy, 175HP EVINRUDE
E135FCXSNF, E135FCXSOB, E135FCXSRM, E135FCXSTA, E135FPLSOB, E135FPLSRM, E135FPLSTA, E135FPLSTF, E135FPXSOB, E135FPXSRM, E135FSLSTA, E135FSLSTF, E150FCXSNF, E150FCXSOC, E150FCXSRS, E150FCXSTD, E150FHLSOC, E150FHLSRS, E150FPLSOC, E150FPLSRS, E150FPLSTD
CYL
Price: query
Rating:
Compatible models:
E135FCXSNF
E135FCXSOB
E135FCXSRM
E135FCXSTA
E135FPLSOB
E135FPLSRM
E135FPLSTA
E135FPLSTF
E135FPXSOB
E135FPXSRM
E135FSLSTA
E135FSLSTF
E150FCXSNF
E150FCXSOC
E150FCXSRS
E150FCXSTD
E150FHLSOC
E150FHLSRS
E150FPLSOC
E150FPLSRS
E150FPLSTD
E150FPLSTF
E150FPXSOC
E150FPXSRS
E150FSLSTF
E175FCXSNF
E175FCXSOD
E175FCXSRE
E175FCXSTB
E175FPLSOD
E175FPLSRE
E175FPLSTB
E175FPLSTF
E175FPXSOD
E175FPXSRE
E175FSLSTF
E175MFXSOS
EVINRUDE
BRP EVINRUDE entire parts catalog list:
- CYLINDER & CRANKCASE » 5001965
E135FCXSRM 2004
E135FCXSTA 2003
E135FPLSOB, E135FSLSOB 2004,2005
E135FPLSRM, E135FSLSRM 2004
E135FPLSTA, E135FPXSTA 2003
E135FPLSTF 2003
E135FPXSOB 2004,2005
E135FPXSRM 2004
E135FSLSTA 2003
E135FSLSTF 2003
E150FCXSNF, E150FPLSNF, E150FPXSNF 2002
E150FCXSOC 2004,2005
E150FCXSRS 2004
E150FCXSTD 2003
E150FHLSOC 2004,2005
E150FHLSRS 2004
E150FPLSOC, E150FSLSOC 2004,2005
E150FPLSRS, E150FSLSRS 2004
E150FPLSTD, E150FPXSTD, E150FSLSTD 2003
E150FPLSTF 2003
E150FPXSOC 2004,2005
E150FPXSRS 2004
E150FSLSTF 2003
E175FCXSNF, E175FPLSNF, E175FPXSNF 2002
E175FCXSOD 2004,2005
E175FCXSRE 2004
E175FCXSTB 2003
E175FPLSOD, E175FSLSOE 2004,2005
E175FPLSRE, E175FSLSRB 2004
E175FPLSTB, E175FPXSTB, E175FSLSTM 2003
E175FPLSTF 2003
E175FPXSOD 2004,2005
E175FPXSRE 2004
E175FSLSTF 2003
E175MFXSOS 2005
E175MFXSOS 2004
Information:
1. Remove cover (1), plate assembly (2), and adapter group (3) from the governor. 2. Remove the bolt that holds collar (4) on the bolt. Remove cover (5) and the spring under the collar. 3. Remove bolts (6) and governor housing (7). Remove the gasket that is under the governor housing. 4. Disconnect two fuel lines (8) from the plate group. Remove seat (9) and spring (10). 5. Remove bolts (12) that hold the plate group (13) on the fuel injection pump housing. Remove the plug from the side of the fuel injection pump housing and install tooling (A).6. Pull the bolt (11) up to put the rack in the center position. The rack is in the center position when it is against tool (A).7. Remove adapter group (13). Keep bolt (11) pulled up to keep the rack in the center position. If the rack is not in the center position, the lever on the bottom of the plate group will prevent the plate group from being removed from the fuel injection pump housing.Install Governor (Dashpot Governor)
Do not install the plate group until drive assembly (3) is removed from the plate group.
1. Remove ring (1), dowel (2), and drive assembly (3) from the plate group. 2. Install tool (A) in the side of the fuel injection pump housing. Move the rack against tool (A). This puts the rack in the center position. The fuel rack must be in the center position so lever (5) can be put in alignment with the groove (slot) in the rack. A small amount of force on the end of tool (A) will be needed to keep the rack in the center position.3. Install plate group (4) on the fuel injection pump housing. Make sure lever (5) aligns with the groove (slot) in the rack. Remove tool (A). 4. Install drive assembly (7) in the drive group. Make sure that the groove in the bottom of the drive assembly is in alignment with the pin in the pinion in the fuel injection pump housing. Make sure hole (6) and hole (9) in gear (8) are in alignment. 5. Install pin (11) that holds drive assembly (7) in position in gear (8).6. Install ring (10) to hold pin (11) in position in the gear. 7. Connect two fuel lines (12) to the plate group.8. Install spring (14) and seat (13). 9. Install gasket (16) and governor housing (15). Install the bolts that hold it in place. 10. Install spring (18) and collar (17) on bolt (19). Install the bolt that holds the collar on bolt (19). 11. Install gasket (22) and adapter group (20) on the governor housing. Make sure lever (21) is in position under collar (17). 12. Put the gasket and plate assembly (24) in position on adapter group (20). Make sure the pin on plate assembly (24) is in the groove (slot) in the collar.13. Install the gaskets and two covers (23) on the plate assembly.14. Check the governor adjustment. See "Governor Adjustments" in the Testing and Adjusting manual.
Do not install the plate group until drive assembly (3) is removed from the plate group.
1. Remove ring (1), dowel (2), and drive assembly (3) from the plate group. 2. Install tool (A) in the side of the fuel injection pump housing. Move the rack against tool (A). This puts the rack in the center position. The fuel rack must be in the center position so lever (5) can be put in alignment with the groove (slot) in the rack. A small amount of force on the end of tool (A) will be needed to keep the rack in the center position.3. Install plate group (4) on the fuel injection pump housing. Make sure lever (5) aligns with the groove (slot) in the rack. Remove tool (A). 4. Install drive assembly (7) in the drive group. Make sure that the groove in the bottom of the drive assembly is in alignment with the pin in the pinion in the fuel injection pump housing. Make sure hole (6) and hole (9) in gear (8) are in alignment. 5. Install pin (11) that holds drive assembly (7) in position in gear (8).6. Install ring (10) to hold pin (11) in position in the gear. 7. Connect two fuel lines (12) to the plate group.8. Install spring (14) and seat (13). 9. Install gasket (16) and governor housing (15). Install the bolts that hold it in place. 10. Install spring (18) and collar (17) on bolt (19). Install the bolt that holds the collar on bolt (19). 11. Install gasket (22) and adapter group (20) on the governor housing. Make sure lever (21) is in position under collar (17). 12. Put the gasket and plate assembly (24) in position on adapter group (20). Make sure the pin on plate assembly (24) is in the groove (slot) in the collar.13. Install the gaskets and two covers (23) on the plate assembly.14. Check the governor adjustment. See "Governor Adjustments" in the Testing and Adjusting manual.
Parts cyl EVINRUDE:
5000822
5000822 CYL & C/C Assy, 135, 150HP
E135FCXSDE, E135FCXSNF, E135FCXSOB, E135FCXSRM, E135FCXSTA, E135FPLSDE, E135FPLSOB, E135FPLSRM, E135FPLSTA, E135FPLSTF, E135FPXSDE, E135FPXSOB, E135FPXSRM, E135FSLSDE, E135FSLSTA, E135FSLSTF, E150FCXSDR, E150FCXSNF, E150FCXSOC, E150FCXSRS, E150FCXSTD