5001510 EVINRUDE CYLINDER HEAD, Stbd.

Illustration 1 g01240739
Schematic for the pressure sensor supply
Illustration 2 g01240816
Sensor locations for the pressure sensor supply
(1) Intake manifold pressure sensor
(2) Fuel pressure sensor
(3) Atmospheric pressure sensor
(4) Engine oil pressure sensor
(5) J2/P2 ECM connectors
Illustration 3 g01204484
Terminal locations at the P2 ECM connector for the engine pressure sensors
(P2-15) Boost pressure sensor
(P2-17) Sensor return
(P2-28) Engine oil pressure sensor
(P2-40) Fuel pressure sensor
(P2-57) Atmospheric pressure sensor
(P2-72) Pressure sensor supply
Illustration 4 g01240891
Terminal locations at the sensor connector for the engine pressure sensors
(1) Pressure sensor supply
(2) Sensor return
(3) Sensor signal Test Step 1. Determine if the Code is Logged or Active
Connect Cat ET to the service tool connector.
Restore electrical power to the engine ECM.
Monitor the active diagnostic code and the logged diagnostic codes on Cat ET. Note: Wait at least 30 seconds in order for diagnostic codes to become active.Identify the diagnostic code.Results:
Logged code - Repair: Do not troubleshoot a logged code unless the code relates to an operator complaint. If the code is logged and the code does not relate to an operator complaint, clear the code.If the code is logged and the code relates to an operator complaint, proceed to Test Step 2.
Active code - Proceed to Test Step 3.Test Step 2. Check the Integrity of the Connections at the Connectors
Turn the keyswitch to the ON position. Do not start the engine.
Install a 7X-1708 Multimeter Probe (RED) and a 7X-1709 Multimeter Probe (BLACK) onto the test leads of a multimeter. Note: Ensure that the multimeter probes are in good repair. Bent probes may contact other terminals in the connector.
Check for an intermittent problem at the connector for the suspect sensor: Note: Do not disconnect any harness connectors in order to perform this procedure.
Carefully install the spoons (multimeter probes) into the terminal locations for the pressure sensor supply and the sensor return at the P2 ECM connector.
While you observe the voltage reading on the multimeter, wiggle the wires and pull on the wires at the connector for the suspect sensor. The voltage reading will not vary more than 0.5 volts for a solid electrical connection.
Remove the spoons (multimeter probes) from the connector.
Check for an intermittent problem at the ECM connector: Note: Do not disconnect any harness connectors in order to perform this procedure.
Carefully install the spoons (multimeter probes) into the terminal locations for the pressure sensor supply and the sensor return at the connector for the suspect sensor.
While you observe the voltage reading on the multimeter, wiggle the wires and pull on the wires for the pressure sensor supply and the sensor return at the ECM connector. The voltage reading will not vary more than 0.5 volts for a solid electrical connection.
Remove the spoons (multimeter probes) from the connector.
Turn the keyswitch to the OFF position. Expected Result:The voltage reading did not vary more than 0.5 volts during either test.Results:
OK - The voltage reading did not vary more than 0.5 volts.Repair: The connections are OK at the connectors. There does not appear to be an intermittent problem in the circuit at this time. Return the engine to service.STOP
Not OK - The voltage reading varied more than 0.5 volts during the test.Repair: Disconnect the suspect connector and inspect the connector and the terminals for moisture, damage, and corrosion. Repair the connectors and/or the terminals. Return the engine to service.STOPTest Step 3. Check the Supply Voltage at the Sensor ConnectorMeasure the voltage between terminal 1 (pressure sensor supply) and terminal 2 (sensor return) at the harness connector for the sensor that relates to the code.Expected Result:The voltage is between 4.5 VDC and 5.5 VDC.Results:
OK - The voltage is between 4.5 VDC and 5.5 VDC. The supply voltage is at the sensor connector. Record the voltage measurement. If you are troubleshooting a -3 diagnostic code, proceed to Test Step 4. If you are troubleshooting a -4 diagnostic code, proceed to Test Step 7.
Not OK - The voltage is less than 4.5 VDC or the voltage is greater than 5.5 VDC.Repair: The voltage of the sensor supply is incorrect. Refer to Troubleshooting, "5 Volt Engine Pressure Sensor Supply Circuit - Test".STOPTest Step 4. Check for Battery Voltage on the Signal WireMeasure the voltage between the signal terminal and the return terminal on the harness connector for the sensor that relates to the diagnostic code.Expected Result:The voltage measurement is less than the +Battery voltage.Results:
OK - The voltage measurement is less than the +Battery voltage. The signal wire is not shorted to the +Battery. Proceed to Test Step 5.
Not OK - The voltage measurement is approximately equal to the +Battery voltage. The signal wire is shorted to the +Battery.Repair: Repair the wiring, when possible. Replace parts, if necessary. Verify that the problem is resolved.STOPTest Step 5. Check the Signal Wire for an Open Circuit
Disconnect the sensor that relates to the diagnostic code.
Connect a jumper wire between the signal terminal and the return terminal on the harness connector for the sensor that relates to the diagnostic code. This will replace the sensor with a short circuit.
Look for a -4 diagnostic code. Expected Result:The -3 code does not change to a -4 code when the jumper wire is connected.Results:
OK - The -3 code does not change to a -4 code when the jumper wire is connected. Connect the sensor. There is a problem with the wiring harness or with the ECM. Proceed to Test Step 6.
Not OK - The -3 code changes to a -4 code when the jumper wire is connected. The wiring harness and the ECM are OK.Repair: Perform the following procedure:
Remove the jumper wire.
Connect a new sensor to the engine harness. Do not install the sens