5008773 EVINRUDE CYLINDER SEAL KIT


5008773 CYLINDER SEAL KIT EVINRUDE E115DHLAAA, E115DHLABA, E115DSLAAA, E115DSLABA, E130DPLAAA, E130DPLABA, E130DSLAAA, E130DSLABA, E75DPLAAA, E75DSLAAA, E90DPLAAA, E90DPXAAA, E90DSLAAA CYLINDER
5008773 CYLINDER SEAL KIT EVINRUDE
Rating:
75

Buy CYLINDER SEAL KIT 5008773 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$63.99

18-06-2025

US: QLZOZB
Trim Piston Repair Seal Kit Fit for Evinrude E-Tec 2004-2012 3 Cylinder and V4 Engines Replace 5008985 5008773 5005756 5007776 5008949
QLZOZB Comprehensive Repair: The kit includes all the seals required to repair the trim piston, which can effectively solve the oil leakage problem caused by aging and wear of seals, restore the normal working pressure of the engine hydraulic system, and improve the maneuverability of the ship || High Quality Materials: The kit is made of high-quality rubber and corrosion-resistant materials, with good sealing and wear resistance, which can effectively prevent oil leakage, extend the service life of the trim piston, and ensure stable operation of the engine under various working conditions || When Does It Need to Be Replaced? When the engine experiences problems such as insufficient power, high oil consumption, difficulty starting, unstable idle, severe cylinder wear, and inability to dissipate heat, please check and replace it in a timely manner || Easy to Install: Easy to install, directly replace, easy to install, no need for modification, can restore the normal function of the engine trim piston || Perfect Fit: This repair seal kit fit for Evinrude ETEC 2004-2012 3 Cylinder and V4 Engines, replace 5008985 5008773 5005756 5007776 5008949
$54.00

12-06-2025

US: Oumao Part
Trim Piston Repair Seal Kit Compatible With 2004-2012 Evinrude ETEC 5008985 & 5008773 (Replace#5005756, 5007776, 5008949)
Neopaftu Precise Compatibility:Fits 2004-2012 Evinrude E-TEC 3 Cylinder & V4 Engines (75/90HP 1.3L Inline, 115/130HP 1.7L V4) - Includes 5008985 & 5008773 trim piston repair seal kits. || OEM Replacement Solution:Directly replaces worn-out parts #5005756, 5007776, and 5008949 to restore factory-grade hydraulic trim/tilt performance. || Leak Prevention & Function Restoration:Rebuilds trim piston seals to eliminate fluid leaks and ensures smooth outboard motor trimming/tilting operations. || Durable Material Construction:High-grade seals and components engineered to withstand marine environments and repeated hydraulic pressure cycles. || Complete Repair Package:Contains all necessary seals and gaskets for full trim piston overhaul - includes detailed installation guidance for DIY maintenance.
$64.99

30-04-2025

CN: Ciuouient
Ciuouient 5008985 & 5008773 Trim Piston Repair Seal Kit Compatible With 2004-2012 Evinrude ETEC(Replace#5005756, 5007776, 5008949)
Ciuouient APPLICABLE MODELS: 5008985&5008773 Trim Piston Repair Seal Kits compatible with 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012 Evinrude E-Tec 3 Cylinder and V4 Engines 75&90 HP 1.3L Inline, 115 & 130 HP 60 degree V4 1.7L  || PART NUMBER: 5008985&5008773 Trim Piston Repair Seal Kits || PACKAGE INCLUDED: A Set of Trim Piston Repair Seal Kit
Number on catalog scheme: 24
 

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 5P-7306 Housing 1
5P-7305 Gear 1
B 5P-7305 Timing Pin (Crankshaft) 1
268-1966 Adapter
C 1P-2320 Combination Puller 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all hoses, on all hose assemblies and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. Plugging hose assemblies helps to prevent fluid loss. Plugging hose assemblies helps to keep contaminants from entering the system.
Do not disconnect the air lines until the air pressure in the system is at zero. If hose is disconnected under pressure it can cause personal injury.
Release the pressure from the air system. Refer to the Original Equipment Manufactures (OEM) for the correct procedure.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
If the engine is equipped with a hydraulic pump on the rear of the air compressor, remove the hydraulic pump. Refer to the (OEM for the correct procedure.
Illustration 1 g02710999
Typical example
Remove plug (2) from the cylinder block. Remove O-ring seal (1) from plug (2).
Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure. Note: The air compressor must be timed with the engine in order to minimize engine vibration.
Install Tooling (B) into Hole (X) in the cylinder block. Use Tooling (B) in order to lock the crankshaft in the correct position. Note: Do not use excessive force to install Tooling (B). Do not use Tooling (B) to hold the crankshaft during repairs.
Illustration 2 g02711018
Typical example
Illustration 3 g02711019
Typical example
Illustration 4 g02711020
Typical example
Disconnect coolant hose (3) and hose (4) from air compressor (6).
Disconnect the air lines from port (5) and port (7). Refer to the OEM for the correct procedure.
Remove tube assembly (9) from air compressor (6) and from the cylinder block.
Remove bolt (10) and bolt (12) from support bracket (11) and remove the support bracket.
Support air compressor (6). Remove nuts (15) and remove the air compressor from front housing (8).
Remove O-ring seal (20) from air compressor (6).
If necessary, remove bolts (17) and remove plate (16). Remove O-ring seal (13) from plate (16). Refer to Illustration 3.
If necessary, follow Step 14.a through Step 14.b in order to remove the gear from the compressor.
Remove nut (19) and remove the spring washer.
Use Tooling (C) in order to remove gear (18) from the crankshaft of air compressor (6). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty


Parts cylinder EVINRUDE:

5007398
 
5007398 CYLINDER/CRANKCASE Assy
E75DPLAAA, E75DPLIIS, E75DPLINC, E75DPLISD, E75DPLISF, E75DPLSCB, E75DPLSEE, E75DSLAAA, E75DSLIIA, E75DSLINM, E75DSLISF, E75DSLISR, E75DSLSCS, E75DSLSEC, E90DMXSES, E90DPLAAA, E90DPLIIS, E90DPLINC, E90DPLISD, E90DPLISF, E90DPLSCB, E90DPLSEE, E90DPXAA
5007480
 
5007480 CYLINDER HEAD
E75DPLAAA, E75DPLIIS, E75DPLINC, E75DPLISD, E75DPLISF, E75DPLSCB, E75DPLSEE, E75DSLAAA, E75DSLIIA, E75DSLINM, E75DSLISF, E75DSLISR, E75DSLSCS, E75DSLSEC, E90DMXSES, E90DPLAAA, E90DPLIIS, E90DPLINC, E90DPLISD, E90DPLISF, E90DPLSCB, E90DPLSEE, E90DPXAA
5007555
 
5007555 CYLINDER / CRANKCASE Assy
E115DBXAAA, E115DBXABA, E115DBXIIB, E115DBXINE, E115DBXISF, E115DBXSEF, E115DCXAAA, E115DCXABA, E115DCXIIA, E115DCXINM, E115DCXISF, E115DCXSEF, E115DHLAAA, E115DHLABA, E115DHLIIR, E115DHLINA, E115DHLISC, E115DHLSES, E115DHXAAA, E115DHXABA, E115DHXIIR
Back to top