5041403 CYLINDER & CRANKCASE ASSEMBLY EVINRUDE
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, E10EL4AAB, E10EL4INS, E10PL4INS, E10TEL4AAB
CYLINDER
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- CYLINDER & CRANKCASE ASSEMBLY » 5041403
B10EL4INS 2012
B10PL4AAA, B10PX4AAA, E10PL4AAA, E10PX4AAA 2012
B10PL4AAB, B10PX4AAB, E10PL4AAB, E10PX4AAB 2012
B10PL4INS 2012
B10PX4INS, E10PX4INS 2012
B10R4AAA, B10RL4AAA, E10R4AAA, E10RL4AAA 2012
B10R4AAB, B10RL4AAB, B10TEL4AAB, E10R4AAB, E10RL4AAB 2012
B10R4INS, E10R4INS 2012
B10RL4INS, E10RL4INS 2012
B10TEL4AAA, E10TEL4AAA 2012
B10TEL4INS, E10TEL4INS 2012
B10TPL4AAA, B10TPX4AAA, E10TPL4AAA, E10TPX4AAA 2012
B10TPL4AAB, B10TPX4AAB, E10TPL4AAB, E10TPX4AAB 2012
B10TPL4INS, E10TPL4INS 2012
B10TPX4INS, E10TPX4INS 2012
E10EL4AAB 2012
E10EL4INS 2012
E10PL4INS 2012
E10TEL4AAB 2012
Information:
start by:a) remove piston cooling jets1. Drain the oil from the oil pan.2. Use tool (A) to turn the engine flywheel to move counterweights (1) in position for removal. Remove counterweights (1) from the crankshaft through the side of the cylinder block.3. Use tool (A) and turn the engine flywheel to move the connecting rod bearing surface (journal) to the top center position.4. Use tool (B) and loosen the four bolts that hold the main bearing cap in position.5. Hold the main bearing cap in position with a pry bar and remove the bolts and lower the bearing cap from the cylinder block.6. Remove the bearing caps from the side of the engine. The weight of the bearing cap is 16 kg (35 lb.).7. Remove the lower bearing half (2) from bearing cap (3).8. Remove thrust plates (4) from each side of the center main bearing.
CAUTION If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and cylinder block. This can cause damage to either or both.
On the center main journal that has no oil hole, put a thin piece of soft material that will not damage the crankshaft journal against the end of the bearing, opposite the tab. Hit the bearing with the soft material until the tab of the bearing is free from the cylinder block. Remove the upper half of the main bearing.9. Install tool (C) in the oil hole in the crankshaft journal and remove upper main bearing halves (5) as the crankshaft is turned and the bearing is moved out of the cylinder block. INSTALL CRANKSHAFT MAIN BEARINGS
CAUTION Make sure the upper and lower halves of bearings are installed so the bearing tabs fit into the notch in cylinder block and bearing caps.
Install the main bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly.1. Install tool (B) in the oil hole of the crankshaft. Put the upper bearing half (half with oil hole) in position on the crankshaft. Use tool (A) to turn the engine flywheel and push the bearing half in position with tool (B).2. Make sure the bearing caps are clean and install the lower bearing halves in the caps.
CAUTION Do not use and impact wrench to tighten the bolts the additional 180 5° of a turn more.
When the bearing clearance is checked and the engine is in a vertical position, such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with the Plastigage. The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances.3. Check the bearing clearances with Plastigage as follows:a) Put a piece of Plastigage on the surface of the lower bearing half.b) Install the main bearing caps with the word "FRONT" and the cast part number toward the front of the cylinder block. Each cap has a number on the bottom surface and must be installed in the same position as the correct number on the right side of the block pan rail.c) Apply clean engine oil on the main bearing cap bolts and tighten them in the number sequence shown with tool (D) to a torque of 190 14 N m (140 10 lb.ft.). Then tighten the bolts in the number sequence shown 180 5° of a turn more.d) Remove the caps and measure the Plastigage. The main bearing clearance must be 0.122 to 0.241 mm (.0048 to .0095 in.). 4. Put clean engine oil on the thrust plates (5) and install them on each side of the center main bearing with the grooves in the plate against the crankshaft.5. Put clean engine oil on bearings (7) and put bearing caps (6) in position and tighten the bolts as in Step 3.
CAUTION Each counterweight has a number and must be installed in the same position as the correct number on the crankshaft mounting pad to prevent damage to the crankshaft when the engine is run. Also do not use and impact wrench to tighten the bolts the additional 120 5 degrees.
6. Make sure the dowels are in position and install counterweights (8) on the crankshaft. Put 6V-4876 Lubricant on the bolt threads, the bolt shank and the underside of the bolt head. Do not use any other lubricant on the bolt threads. For 3508 engines follow steps 6a thorough 6d for the correct torquing procedure. For 3512 and 3516 engines follow steps 6e through 6f for the correct torquing procedure.a) Tighten the bolts evenly to a torque of 200 5 N m (145 4 lb ft).b) Loosen the bolts.c) Tighten the bolts evenly to a torque of 70 5 N m (50 4 lb ft).d) Put a mark on each bolt head and tighten each bolt an additional 120 5 degrees.e) Tighten the bolts evenly to a torque of 70 5 N m (50 4 lb ft).f) Put a mark on each bolt head and tighten each bolt an additional 120 5 degrees.7. Check the crankshaft end play with tooling (C). The end play is controlled by the thrust pates on the center main bearing. End play with new bearing must be 0.15 to 0.50 mm (.006 to .020 in).8. Fill the engine with oil to the correct level.end by:a) install piston cooling jets
CAUTION If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and cylinder block. This can cause damage to either or both.
On the center main journal that has no oil hole, put a thin piece of soft material that will not damage the crankshaft journal against the end of the bearing, opposite the tab. Hit the bearing with the soft material until the tab of the bearing is free from the cylinder block. Remove the upper half of the main bearing.9. Install tool (C) in the oil hole in the crankshaft journal and remove upper main bearing halves (5) as the crankshaft is turned and the bearing is moved out of the cylinder block. INSTALL CRANKSHAFT MAIN BEARINGS
CAUTION Make sure the upper and lower halves of bearings are installed so the bearing tabs fit into the notch in cylinder block and bearing caps.
Install the main bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly.1. Install tool (B) in the oil hole of the crankshaft. Put the upper bearing half (half with oil hole) in position on the crankshaft. Use tool (A) to turn the engine flywheel and push the bearing half in position with tool (B).2. Make sure the bearing caps are clean and install the lower bearing halves in the caps.
CAUTION Do not use and impact wrench to tighten the bolts the additional 180 5° of a turn more.
When the bearing clearance is checked and the engine is in a vertical position, such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with the Plastigage. The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances.3. Check the bearing clearances with Plastigage as follows:a) Put a piece of Plastigage on the surface of the lower bearing half.b) Install the main bearing caps with the word "FRONT" and the cast part number toward the front of the cylinder block. Each cap has a number on the bottom surface and must be installed in the same position as the correct number on the right side of the block pan rail.c) Apply clean engine oil on the main bearing cap bolts and tighten them in the number sequence shown with tool (D) to a torque of 190 14 N m (140 10 lb.ft.). Then tighten the bolts in the number sequence shown 180 5° of a turn more.d) Remove the caps and measure the Plastigage. The main bearing clearance must be 0.122 to 0.241 mm (.0048 to .0095 in.). 4. Put clean engine oil on the thrust plates (5) and install them on each side of the center main bearing with the grooves in the plate against the crankshaft.5. Put clean engine oil on bearings (7) and put bearing caps (6) in position and tighten the bolts as in Step 3.
CAUTION Each counterweight has a number and must be installed in the same position as the correct number on the crankshaft mounting pad to prevent damage to the crankshaft when the engine is run. Also do not use and impact wrench to tighten the bolts the additional 120 5 degrees.
6. Make sure the dowels are in position and install counterweights (8) on the crankshaft. Put 6V-4876 Lubricant on the bolt threads, the bolt shank and the underside of the bolt head. Do not use any other lubricant on the bolt threads. For 3508 engines follow steps 6a thorough 6d for the correct torquing procedure. For 3512 and 3516 engines follow steps 6e through 6f for the correct torquing procedure.a) Tighten the bolts evenly to a torque of 200 5 N m (145 4 lb ft).b) Loosen the bolts.c) Tighten the bolts evenly to a torque of 70 5 N m (50 4 lb ft).d) Put a mark on each bolt head and tighten each bolt an additional 120 5 degrees.e) Tighten the bolts evenly to a torque of 70 5 N m (50 4 lb ft).f) Put a mark on each bolt head and tighten each bolt an additional 120 5 degrees.7. Check the crankshaft end play with tooling (C). The end play is controlled by the thrust pates on the center main bearing. End play with new bearing must be 0.15 to 0.50 mm (.006 to .020 in).8. Fill the engine with oil to the correct level.end by:a) install piston cooling jets
Parts cylinder EVINRUDE:
5041400
5041400 CYLINDER HEAD COMPLETE
B10EL4AAA, B10EL4INS, B10PL4AAA, B10PL4INS, B10PX4INS, B10R4AAA, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4INS, B10TPX4INS
5041270
5041270 CYLINDER HEAD GASKET
B10EL4AAA, B10EL4INS, B10PL4AAA, B10PL4INS, B10PX4INS, B10R4AAA, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4INS, B10TPX4INS
5041402
5041402 CYLINDER HEAD COVER
B10EL4AAA, B10EL4INS, B10PL4AAA, B10PL4INS, B10PX4INS, B10R4AAA, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4INS, B10TPX4INS
5041271
5041271 CYLINDER HEAD COVER GASKET
B10EL4AAA, B10EL4INS, B10PL4AAA, B10PL4INS, B10PX4INS, B10R4AAA, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4INS, B10TPX4INS
5041500
5041500 CYLINDER PIN (LOWER)
B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, E10PL4INS, E15PL4INS