0215188 EVINRUDE *DECAL, Rear, 225FH


0215188 *DECAL, Rear, 225FH EVINRUDE E200FCXSIF, E225FCXSIF, E225FPLSIF, E250FCXSIF DECAL
0215188 *DECAL, Rear, 225FH EVINRUDE
Rating:
73

Buy *DECAL, Rear, 225FH 0215188 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E200FCXSIF, E200FPLSIF, E200FPXSIF, E200FSLSIF, RE200FCSIF, RE200FLSIF, RE200FSSIF, RE200FXSIF 2001
E225FCXSIF, E225FCZSIF, E225FHLSIF, E225FPXSIF, E225FPZSIF, RE225FCSIF, RE225FHSIF, RE225FXSIF, RE225FZSIF 2001
E225FPLSIF 2001,2003
E250FCXSIF, E250FCZSIF, E250FPXSIF, E250FPZSIF 2001

Information:


Table 1
Engine Arrangement
Original Engine Replacement Engine
7E-9078 195-3816(1)
10R-5596(2)
121-5777
(1) New Repower Engine - Requires Software
(2) Reman Engine - Requires SoftwareThis Special Instruction does not include procedures that can be found in your existing manuals. Refer to the original Service Manual, Parts Manual, and Operation and Maintenance Manual for more information.When you have completed this procedure, prepare the machine for service. Refer to the Operation and Maintenance Manual.Note: Do not perform any procedure in this Special Instruction until the information has been read and understood.Reference: Service Manual, Parts Manual, Operation and Maintenance Manual.Note: This instruction contains some procedures that come from dealer feedback. If errors are found, contact the Emissions Retrofit Group.New Engine Information Label
This repower process will require the engine to be reflashed with new software. Use a new engine information label by using the standard process before performing the repower.Registering the Repower Machine
Reference: Special Instruction, REHS5097, "Instructions to Register the Retrofit"Document change to a machine configuration is an advantage to Caterpillar and the dealer technicians that are sent to repair a machine. By identifying that the machine has been reconfigured, the technician will have a better opportunity to have the correct parts, tooling, and service information. Identifying that the machine has been reconfigured will also allow Caterpillar to include the retrofitted serial numbers in applicable Service Letters.Safety
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Do not attempt to assemble this machine until you read and you understand the assembly instructions.Improper assembly procedures could result in injury or death.
Personal injury or death can result from improper lifting or blocking.When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component.Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Welding on Electronically Controlled Engines
Proper welding procedures are necessary to avoid damage to electronic controls. Perform welding on the engine according to the following procedure.
Set the engine control to the "STOP" mode.
Turn OFF the fuel supply to the engine.
Disconnect the negative terminal from the battery.
Disconnect the engine electronic components from the wiring harnesses: ECM, throttle actuator, actuator for the turbocharger compressor bypass, fuel metering valve, and sensors.
Protect the wiring harnesses from welding debris and/or from welding spatter.
Do NOT use electrical components (ECM or sensors) or electronic component grounding points for grounding the welder.
Connect the ground cable of the welder directly to the engine component that will be welded. Place the clamp as close as possible to the weld to reduce the possibility of welding current damage.
Use standard welding procedures to weld the materials together.Required Parts
Refer to Parts Manual, SEBP4392.Note: The required parts are subject to some change. Refer to TMI for the most recent required parts list.Note: If part fabrication is necessary, ensure that all fabricated parts are deburred. Use caution when deburring parts. Avoid excessive grinding and notches.Note: A breakdown of the kit provides a parts list for the repower. The kit part number is not serviceable. Order the engine arrangement plus the list of parts provided in the kit.
Table 2
Repower Parts
( 291-5597 Conversion Ar-Repower)
Qty Part No


Parts decal EVINRUDE:

0214915
 
0214915 *DECAL, Front (white)
E200FCXSIF, E225FCXSIF, E225FPLSIF, E250FCXSIF
0215167
 
0215167 *DECAL, Front (blue)
E200FCXSIF, E225FCXSIF, E225FPLSIF, E250FCXSIF
0214899
 
0214899 *DECAL, Front (blue)
E200FCXSIF, E200WPXSIF, E225FCXSIF, E225FPLSIF, E250FCXSIF
0214897
 
0214897 *DECAL, Wrap (blue)
E200FCXSIF, E225FCXSIF, E225FPLSIF, E250FCXSIF
0214913
 
0214913 *DECAL, Wrap (white)
E200FCXSIF, E225FCXSIF, E225FPLSIF, E250FCXSIF
0215165
 
0215165 *DECAL, Wrap (blue)
E200FCXSIF, E225FCXSIF, E225FPLSIF, E250FCXSIF
0214917
 
0214917 *DECAL, Rear, 225FPX, FX, FPZ, FCX, FC, FCZ
E200FCXSIF, E225FCXSIF, E225FPLSIF, E250FCXSIF
0214916
 
0214916 *DECAL, Rear, 200FSL, FPX, FX, FCX, FC
E200FCXSIF, E225FCXSIF, E225FPLSIF, E250FCXSIF
Back to top