0283486 EVINRUDE DECAL SET, Evinrude

Table 1
J1939 Code and Description CDL Code and Description Comments
1180-3
Engine Turbocharger 1 Turbine Inlet Temperature : Voltage Above Normal 3908-3
Engine Turbocharger #1 Turbine Intake Temperature Sensor : Voltage Above Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1180-4
Engine Turbocharger 1 Turbine Inlet Temperature : Voltage Below Normal 3908-4
Engine Turbocharger #1 Turbine Intake Temperature Sensor : Voltage Below Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1180-8
Engine Turbocharger 1 Turbine Inlet Temperature : Abnormal Frequency, Pulse Width, or Period 3908-8
Engine Turbocharger #1 Turbine Intake Temperature Sensor : Abnormal Frequency, Pulse Width, or Period If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1181-3
Engine Turbocharger 2 Turbine Inlet Temperature : Voltage Above Normal 3909-3
Engine Turbocharger #2 Turbine Intake Temperature Sensor : Voltage Above Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1181-4
Engine Turbocharger 2 Turbine Inlet Temperature : Voltage Below Normal 3909-4
Engine Turbocharger #2 Turbine Intake Temperature Sensor : Voltage Below Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1181-8
Engine Turbocharger 2 Turbine Inlet Temperature : Abnormal Frequency, Pulse Width, or Period 3909-8
Engine Turbocharger #2 Turbine Intake Temperature Sensor : Abnormal Frequency, Pulse Width, or Period If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1184-3
Engine Turbocharger #1 Turbine Outlet Temperature : Voltage Above Normal 3782-3
Engine Turbocharger #1 Turbine Outlet Temperature Sensor : Voltage Above Normal
1184-4
Engine Turbocharger #1 Turbine Outlet Temperature : Voltage Below Normal 3782-4
Engine Turbocharger #1 Turbine Outlet Temperature Sensor : Voltage Below Normal
1184-8
Engine Turbocharger #1 Turbine Outlet Temperature : Abnormal Frequency, Pulse Width, or Period 3782-8
Engine Turbocharger #1 Turbine Outlet Temperature Sensor : Abnormal Frequency, Pulse Width, or Period
1185-3
Engine Turbocharger #2 Turbine Outlet Temperature : Voltage Above Normal 5725-3
Engine Turbocharger #2 Turbine Outlet Temperature Sensor : Voltage Above Normal
1185-4
Engine Turbocharger #2 Turbine Outlet Temperature : Voltage Below Normal 5725-4
Engine Turbocharger #2 Turbine Outlet Temperature Sensor : Voltage Below Normal
1185-8
Engine Turbocharger #2 Turbine Outlet Temperature : Abnormal Frequency, Pulse Width, or Period 5725-8
Engine Turbocharger #2 Turbine Outlet Temperature Sensor : Abnormal Frequency, Pulse Width, or Period
Illustration 1 g06055125
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -3 code is active or logged.
Proceed to Test Step 2.
Result: A -4 code is active or logged.
Proceed to Test Step 3.
Result: A -8 code is active or logged.
Proceed to Test Step 5.
2. Create a Short at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor with the active -3 code.
C. Install the jumper wire between the following terminals at the sensor connector:
- Pin 2 (sensor return) and